Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Glue\s+for\s+under\s+hood\s+insulation\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Glue\s+for\s+under\s+hood\s+insulation\s*$/: 17 ]

Total 17 documents matching your query.

1. Glue for under hood insulation (score: 1): Author: "Frank T" <dawolfsburg@hotmail.com>; Date: Thu, 15 Jul 2004 10:07:27 -0400; What is a good glue to use when installing under-hood insulation? I have had little success with convincing the material to stay put. My next guess would be contact cement..? It is going on a 1978 MG; /html/mgs/2004-07/msg00307.html (7,935 bytes)
2. Re: Glue for under hood insulation (score: 1): Author: Elliott and Martha DeGraff <degraff@erols.com>; Date: Thu, 15 Jul 2004 10:34:29 -0400; I've had fairly good luck using 3M high strength spray adhesive. It's simple to use and seems to hold for a year or two. It would probably do better had I removed everything and cleaned it properly.; /html/mgs/2004-07/msg00308.html (8,284 bytes)
3. Re: Glue for under hood insulation (score: 1): Author: "Mike Razor" <mrazor@mis.net>; Date: Thu, 15 Jul 2004 10:42:21 -0400; I use a 3M spray glue that is used to glue trim on cars. It comes in a spray can and I have glued lots of stuff to include a felt part that is affixed to the hood and rest on the radiator of my MGA.; /html/mgs/2004-07/msg00309.html (8,139 bytes)
4. Re: Glue for under hood insulation (score: 1): Author: "Paul Hunt" <paul.hunt1@blueyonder.co.uk>; Date: Thu, 15 Jul 2004 15:37:03 +0100; I've used spray adhesive for similar areas as you can get 100% coverage but thinly. A previous attempt to use brush-on contact adhesive resulted in the small area I was trying to stick back becoming; /html/mgs/2004-07/msg00310.html (8,404 bytes)
5. Re: Glue for under hood insulation (score: 1): Author: Bill Saidel <saidel@camden.rutgers.edu>; Date: Thu, 15 Jul 2004 10:57:13 -0400; I use the same (3M) and the nice part about it is as the under-hood insulation begins to sag or separate, I can just respray with the part holding on allowing me to keep its position easily.; /html/mgs/2004-07/msg00311.html (9,065 bytes)
6. Re: Glue for under hood insulation (score: 1): Author: "Frank Krajewski" <frankk@intap.net>; Date: Thu, 15 Jul 2004 11:16:28 -0400; Bill; One of the problems I encountered when installing the hood pad set on my 1980 MGB LE was retaining the pads in place as the glue dried. As soon as I would release them they would sag. I finally; /html/mgs/2004-07/msg00312.html (10,102 bytes)
7. Re: Glue for under hood insulation (score: 1): Author: "Jason Spaeth" <jasonspaeth@hotmail.com>; Date: Thu, 15 Jul 2004 10:51:50 -0500; You can use this same glue for the black covering that is located between the dash and windshield. It is similar to the 3M super 77, except it is made for high temps and it is very expensive. ______; /html/mgs/2004-07/msg00315.html (8,898 bytes)
8. Re: Glue for under hood insulation (score: 1): Author: <ptegler@cablespeed.com>; Date: Thu, 15 Jul 2004 11:56:58 -0400; I use 3M super weather strip adhesive (yellow gorilla snot) You'll use most of a single whole tube, but mine had now been in place for over 6 years of daily driving and has never sagged. Even the edg; /html/mgs/2004-07/msg00316.html (9,321 bytes)
9. Re: Glue for under hood insulation (score: 1): Author: David Councill <dcouncil@imt.net>; Date: Thu, 15 Jul 2004 11:05:50 -0600; The stuff I used was a 3M spray adhesive, high temperature variety. It wasn't terribly expensive - I think Moss sells it for about $15 for a can. I used it for the under hood insulation as well as fo; /html/mgs/2004-07/msg00322.html (8,969 bytes)
10. Re: Glue for under hood insulation (score: 1): Author: Barrie Robinson <barrie@look.ca>; Date: Thu, 15 Jul 2004 20:39:47 -0700; I did a lot of messing about with sound/heatproofing and did do an article in the British V8 Newsletter on it. But briefly what I found was this 1) The DynaMat and similar, is nothing more than the s; /html/mgs/2004-07/msg00327.html (9,475 bytes)
11. Re: Glue for under hood insulation (score: 1): Author: "Paul Hunt" <paul.hunt1@blueyonder.co.uk>; Date: Mon, 19 Jul 2004 12:37:33 +0100; Good point, this reminds me that I used strips of thin lath with the ends just tucked between the 'ribs' of the bonnet and its skin to hold the material in place. PaulH. on; /html/mgs/2004-07/msg00373.html (8,828 bytes)
12. Re: Glue for under hood insulation (score: 1): Author: David Councill <dcouncil@imt.net>; Date: Mon, 19 Jul 2004 08:31:07 -0600; I'll have to revise my earlier reply to this thread. I mentioned that I used the high temperature spray adhesive from Moss. I thought it was 3M but it is not. It has a "Heat" logo on it, looks like i; /html/mgs/2004-07/msg00382.html (9,063 bytes)
13. Re: Glue for under hood insulation (score: 1): Author: Barrie Robinson <barrie@look.ca>; Date: Tue, 20 Jul 2004 10:05:48 -0700; I did a lot of running around when I was investigating sound proofing my-still-in-build-mode MGB GT V8. What I found was a few manufacturers who had special glues for the auto trade - They did not s; /html/mgs/2004-07/msg00394.html (9,832 bytes)
14. Re: Glue for under hood insulation (score: 1): Author: Max Heim <mvheim@studiolimage.com>; Date: Fri, 23 Jul 2004 15:34:19 -0700; On the subject of underhood insulation, I would have thought that the panels supplied by Moss would have been large enough to tuck up under the underhood framing, in order to hide the edges for a nea; /html/mgs/2004-07/msg00474.html (9,049 bytes)
15. Re: Glue for under hood insulation (score: 1): Author: Max Heim <mvheim@studiolimage.com>; Date: Sun, 25 Jul 2004 16:17:56 -0700; Well, I already have the Moss stuff, that's the point. -- Max Heim '66 MGB GHN3L76149 If you're near Mountain View, CA, it's the primer red one with chrome wires; /html/mgs/2004-07/msg00489.html (9,175 bytes)
16. Re: Glue for under hood insulation (score: 1): Author: "Paul Hunt" <paul.hunt1@blueyonder.co.uk>; Date: Mon, 26 Jul 2004 09:30:35 +0100; Same here on both my roadster and V8. Clausagers pictures of a roadster and C seem to show a similar gap, although not an inch, the V8 perhaps not. However if the felt went under the edges it would s; /html/mgs/2004-07/msg00496.html (8,737 bytes)
17. Re: Glue for under hood insulation (score: 1): Author: Max Heim <mvheim@studiolimage.com>; Date: Mon, 26 Jul 2004 08:54:05 -0700; It's not so much sagging (if glued properly that shouldn't be an issue), it's the funky raggedy-looking edges that I was objecting to. -- Max Heim '66 MGB GHN3L76149 If you're near Mountain View, CA,; /html/mgs/2004-07/msg00505.html (9,055 bytes)

Current List: 1 - 17
Page: [1]