Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Tach\s+Conversion\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Tach\s+Conversion\s*$/: 9 ]

Total 9 documents matching your query.

1. Tach Conversion (score: 1): Author: Unknown; Date: Sun, 13 Jul 2003 14:56:00 -0700; I've completed converting my Bugeye over to negative ground, but I am having a problem converting the tachometer from positive ground to negative. The only tach conversion instructions I have been ab; /html/spridgets/2003-07/msg00433.html (8,908 bytes)
2. Re: Tach Conversion (score: 1): Author: Unknown; Date: Sun, 13 Jul 2003 15:36:05 -0700; I could be wrong on this, but I believe you need a negative ground tach. I don't think you can switch them over from positive ground. Gerard 60 Bugeye /// unsubscribe/change address requests to majo; /html/spridgets/2003-07/msg00435.html (9,672 bytes)
3. Re: Tach Conversion (score: 1): Author: Unknown; Date: Sun, 13 Jul 2003 19:17:08 -0500; They can be switched over. Moss publishes the directions for doing so in the MGB catalog. I did this once a couple of years ago when I was switching a pos. ground electric tach to neg. to put in my; /html/spridgets/2003-07/msg00436.html (8,203 bytes)
4. Re: Tach Conversion (score: 1): Author: Unknown; Date: Sun, 13 Jul 2003 19:06:00 -0700; Well, that's good to know. I knew someone would know for sure. It'sbeen so long since I did the one on my Bugeye, I couldn't remember, but I'm sure I just ended up getting a negative ground one anywa; /html/spridgets/2003-07/msg00443.html (8,916 bytes)
5. Re: Tach Conversion (score: 1): Author: Unknown; Date: Sun, 13 Jul 2003 22:05:14 -0400; Remove the guts from the housing, where the green wire spade terminal on the back of the tach is, inside, it is attached to a wire. Next to that wire is a resistor, What you have to do is.... Unsold; /html/spridgets/2003-07/msg00444.html (8,289 bytes)
6. Re: Tach Conversion (score: 1): Author: Unknown; Date: Sun, 13 Jul 2003 22:15:09 -0400; Another conversion is to take a later smaller - grd tach, remove the guts from the housing, a bit of dremel work to the larger housing and the smaller guts will screw right in. Swap the face plate an; /html/spridgets/2003-07/msg00445.html (8,429 bytes)
7. Re: Tach Conversion (score: 1): Author: Unknown; Date: Sun, 13 Jul 2003 22:26:52 -0700; Thanks for all the tips. David - I will download MGB catalog from Moss & check those instructions. Frank - Is the green wire you describe the green wire going TO the tach, connected to the spade term; /html/spridgets/2003-07/msg00448.html (9,104 bytes)
8. tach conversion (score: 1): Author: Unknown; Date: Fri, 7 Jun 2002 17:41:29 -0600 (Mountain Daylight Time); Hello all,=0D Since it seems that there is not much to say on the list today, I will as= k another question.=0D Can anyone direct me on the prtocedure for changing a possitive ground ta= ch to a nega; /html/spridgets/2002-06/msg00341.html (6,575 bytes)
9. Re: tach conversion (score: 1): Author: Unknown; Date: Fri, 07 Jun 2002 21:56:25 -0400; With the tach on the work bench, remove the chrome bezel and glass by twisting and lining up the tabs on the back, sometimes they are stuck, a razor blade around the edge should loosen it up. Remove; /html/spridgets/2002-06/msg00348.html (7,569 bytes)

Current List: 1 - 9
Page: [1]