Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Winch\s+cable\s+support\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Winch\s+cable\s+support\s*$/: 9 ]

Total 9 documents matching your query.

1. Winch cable support (score: 1): Author: "Ted Rodgers" <Rodgers356@email.msn.com>; Date: Mon, 1 May 2000 13:22:36 -0700; When I'm winching my racecar into my trailer the cable scrapes on the floor at the open end until the car is sufficiently up the ramp to bring the cable more level. I'd like to install some kind of r; /html/vintage-race/2000-05/msg00004.html (7,514 bytes)
2. Re: Winch cable support (score: 1): Author: Simon Favre <simon@mondes.com>; Date: Mon, 01 May 2000 19:54:20 -0700; How about mounting a plastic strip along the threshold? I'd say a 1" thick piece of Nylon or Delrin about a foot long would do. You'll probably trip over it though. ;=( Surplus stores often have scra; /html/vintage-race/2000-05/msg00005.html (8,125 bytes)
3. Re: Winch cable support (score: 1): Author: RodsINTOMG@aol.com; Date: Tue, 2 May 2000 08:37:18 EDT; << When I'm winching my racecar into my trailer the cable scrapes on the floor at the open end until the car is sufficiently up the ramp to bring the cable more level. I'd like to install some kind o; /html/vintage-race/2000-05/msg00007.html (7,745 bytes)
4. Re: Winch cable support (score: 1): Author: Mark Haynes <haynes386@netzero.net>; Date: Tue, 02 May 2000 07:19:56 -0600; Ted- An easy, inexpensive way to do this would be to go to your local plastics supply house and buy a scrap piece of UHMWPE (ultra high molecular weight polyethylene) It has great wear characteristic; /html/vintage-race/2000-05/msg00008.html (8,301 bytes)
5. Re: Winch cable support (score: 1): Author: Tombread@aol.com; Date: Tue, 2 May 2000 16:44:42 EDT; << you could use the stuff formula cars use for skid plates. >> That would be the proven high-tech solution used by F1-- a piece of wood. Personally I think wood is much underrated and underutilized; /html/vintage-race/2000-05/msg00017.html (7,592 bytes)
6. Re: Winch cable support (score: 1): Author: Simon Favre <simon@mondes.com>; Date: Tue, 02 May 2000 14:44:19 -0700; You know what they say, if you have a wooden head, use a wooden helmet. ;=) The only kind of wood I'd drag a steel cable across is Lignumvitae. They used to use it for prop shaft bearings on steamshi; /html/vintage-race/2000-05/msg00018.html (7,972 bytes)
7. Re: Winch cable support (score: 1): Author: Bob Spruck <bspruck@mindspring.com>; Date: Tue, 02 May 2000 16:55:44 -0400; I'm only thinking of this because my wife just threw an old one away after buying a new one-- a rolling pin. As is my usual manner, I tried to think of some use for it rather than dispose of it. Coul; /html/vintage-race/2000-05/msg00021.html (8,665 bytes)
8. Re: Winch cable support (score: 1): Author: Brian Evans <brian@uunet.ca>; Date: Wed, 3 May 2000 09:08:31 -0400; At home in my shop I have a stand with a foot wide, 2" diameter steel roller on top that I use as an out-feed support for my table saw. Cost was about $14. Why not take the roller from that and make; /html/vintage-race/2000-05/msg00026.html (9,271 bytes)
9. Re: Winch cable support (score: 1): Author: "Steve Schultz" <sschultz@worldnet.att.net>; Date: Wed, 3 May 2000 22:10:39 -0400; I had the same problem so I bought a 12 inch piece of galvanized strap steel at the hardware store. You know the kind with four countersunk holes already drilled. I screwed it to the floor where the; /html/vintage-race/2000-05/msg00043.html (8,514 bytes)

Current List: 1 - 9
Page: [1]