- 1. RE: Cam timing (score: 1)
- Author: Unknown
- Date: Mon, 8 Nov 2004 10:07:16 -0800
- I don't have my TT catalog handy, but that's a very difficult point to judge accurately. It would be better to find out where one of the valves is supposed to open (and whether the point is "off the
- /html/triumphs/2004-11/msg00145.html (7,019 bytes)
- 2. Re: Cam Timing (score: 1)
- Author: Unknown
- Date: Thu, 26 Aug 1999 21:21:34 -0400
- You asked Andy Mace of VTR about info. related to cam timing... One possible source of info on cam timing on the 'net would be: http://www.ashford-perf.com Joe Perry is the US Piper cam guy. He's go
- /html/triumphs/1999-08/msg02078.html (6,629 bytes)
- 3. Cam Timing (score: 1)
- Author: Unknown
- Date: Thu, 7 Jan 1999 20:07:24 -0500
- Welcome back Larry. We missed you at the Xmas party. 180 degrees off. Was this in in the distributer install part? You are right. The crank goes up and down and up and down. It doesn't know one up fo
- /html/triumphs/1999-01/msg00329.html (7,962 bytes)
- 4. cam timing (score: 1)
- Author: Unknown
- Date: Fri, 4 Apr 1997 18:17:42 PST
- Here is one for the list but I am afraid I already know the answer. I put a new cam in my TR3 motor and timed it per the instructions in the red shop manual for unknown timing. After everything was b
- /html/triumphs/1997-04/msg00238.html (6,892 bytes)
- 5. Re: cam timing (score: 1)
- Author: Unknown
- Date: Fri, 04 Apr 1997 20:55:03 +0000
- Matt Barre wrote:(snip) After everything was buttoned up My mechanic helping me said it would be fine as is - the only sacrifice would be extreme top end but the idle would be better. I don't intend
- /html/triumphs/1997-04/msg00243.html (7,284 bytes)
- 6. Re: cam timing (score: 1)
- Author: Unknown
- Date: Mon, 7 Apr 1997 15:44:29 -0700
- MattThis could be the start of a new adventure...just how late a cam timing can be tolerated by an ex-tractor motor ?? Good thing you don't want to run this car "very hard" as I think anything over
- /html/triumphs/1997-04/msg00338.html (8,281 bytes)
- 7. Re: cam timing (score: 1)
- Author: Unknown
- Date: Tue, 8 Apr 1997 16:02:42 -0700
- Matt sez .<< Part of the problem was the way I was checking the .050 tappet lift - at the valve and spinning the pushrod. After finding excessive duration I realized we had no taken the 1.5 ratio of
- /html/triumphs/1997-04/msg00381.html (8,777 bytes)
- 8. RE: Cam timing (score: 1)
- Author: "Randall" <tr3driver@comcast.net>
- Date: Mon, 8 Nov 2004 10:07:16 -0800
- I don't have my TT catalog handy, but that's a very difficult point to judge accurately. It would be better to find out where one of the valves is supposed to open (and whether the point is "off the
- /html/triumphs/2004-11/msg00701.html (7,385 bytes)
This search system is powered by
Namazu