Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*powdercoating\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*powdercoating\s*$/: 8 ]

Total 8 documents matching your query.

1. Re: Powdercoating (score: 1): Author: mmcewen@gpu.srv.ualberta.ca (John McEwen); Date: Thu, 8 Jan 1998 19:00:03 -0500; Hi Greg: Rust under powdercoat could be a result of the wrong choice of powder. There are three types of powdercoat available, acrylic, urethane and I can't remember the third, but I think it is a hy; /html/mgs/1998-01/msg00630.html (7,986 bytes)
2. powdercoating (score: 1): Author: thomas_pokrefke@juno.com (Thomas J Pokrefke); Date: Thu, 30 Jan 1997 19:25:55 EST; I just looked in the yellow pages for a powdercoater. No one there. Any suggestions as to what I may look under? Thomas James Pokrefke, III 1970 MGB thomas_pokrefke@juno.com http://ocean.st.usm.edu/~; /html/mgs/1997-01/msg01569.html (6,834 bytes)
3. Re: powdercoating (score: 1): Author: dmeadow@juno.com (David C Littlefield); Date: Thu, 30 Jan 1997 20:13:17 EST; Try "Coatings," "Coatings-Protective," "Coatings-Protective-Applicators" Note: Unless you live near a major metropolitan area, you may not find one. Powdercoating equipment is an expensive propositio; /html/mgs/1997-01/msg01572.html (7,369 bytes)
4. Re: powdercoating (score: 1): Author: dmeadow@juno.com (David C Littlefield); Date: Thu, 30 Jan 1997 20:13:17 EST; This thread has come up again only a few weeks since we last addressed and since there are apparently a number of new people that did not get this information the first time, I apologize for repostin; /html/mgs/1997-01/msg01573.html (14,354 bytes)
5. Re: powdercoating (score: 1): Author: "W. R. Gibbons" <gibbons@northpole.med.uvm.edu>; Date: Thu, 30 Jan 1997 21:34:11 -0500 (EST); Try "Coatings" -- I found a couple of outfits that advertise electrostatic coatings. Ray Gibbons Dept. of Molecular Physiology & Biophysics Univ. of Vermont College of Medicine, Burlington, VT gibbon; /html/mgs/1997-01/msg01582.html (7,136 bytes)
6. Re: Powdercoating (score: 1): Author: dmeadow@juno.com (David C Littlefield); Date: Thu, 30 Jan 1997 23:04:21 EST; More apologies to the list. I left out the above subject line in my earlier large posting. Mea culpa David Littlefield Houston, TX; /html/mgs/1997-01/msg01589.html (6,676 bytes)
7. Re: powdercoating (score: 1): Author: car@texas.net (Carol); Date: Fri, 31 Jan 1997 01:28:20 -0600 (CST); You may want to try looking up sandblasters, too. I finally figured out that they usually know a powder coater. Worked for me!! Good luck! Carol; /html/mgs/1997-01/msg01593.html (7,743 bytes)
8. Powdercoating (score: 1): Author: obertro@macatawa.org (robert clark); Date: Tue, 2 Jul 1996 15:03:15 +0100; Have read the last two days of discussion. I powdercoat some of my products on a frequent basis (I make the British Wheel Wrench and other stuff) and so know a bit about it. First, you must take powd; /html/mgs/1996-07/msg00113.html (7,095 bytes)

Current List: 1 - 8
Page: [1]