- 1. [Healeys] BN1/2 Boot Floor Holes (score: 1)
- Author: Bob Spidell <bspidell@comcast.net>
- Date: Fri, 17 Jun 2011 20:31:40 +0000 (UTC)
- In all the excitement over the two low-mileage 100s I noticed something: both cars had small--I'd guess 5/16" dia--holes on either side of the boot pan floor. These holes were about equidistant--i.e.
- /html/healeys/2011-06/msg00523.html (7,100 bytes)
- 2. Re: [Healeys] BN1/2 Boot Floor Holes (score: 1)
- Author: I Erbs <eyera3@gmail.com>
- Date: Fri, 17 Jun 2011 18:05:48 -0700
- My BT7 had about 20 holes drilled into the boot floor by the dpo. I figured he could not locate z boot lid seal so he drained the water out of it..... Ira Erbs IT Consultant Portland, OR sent from my
- /html/healeys/2011-06/msg00529.html (8,902 bytes)
- 3. Re: [Healeys] BN1/2 Boot Floor Holes (score: 1)
- Author: Michael MacLean <rrengineer.mike@att.net>
- Date: Fri, 17 Jun 2011 18:43:17 -0700 (PDT)
- Speaking of holes, I am getting the final welding repair done to my BN2 frame and have noticed numerous holes in the square tubing frame members. How do I know what holes are supposed to be there, if
- /html/healeys/2011-06/msg00530.html (7,859 bytes)
- 4. Re: [Healeys] BN1/2 Boot Floor Holes (score: 1)
- Author: "Tracy Drummond" <bighealey@charter.net>
- Date: Sat, 18 Jun 2011 06:05:16 -0700
- Probably break line retainer clip holes. I bet Dave Nock has photos. My BT7 has them down the frame rails and also on the front cross member where the lines cross over under the radiator area. If you
- /html/healeys/2011-06/msg00533.html (9,854 bytes)
- 5. Re: [Healeys] BN1/2 Boot Floor Holes (score: 1)
- Author: Bob Spidell <bspidell@comcast.net>
- Date: Sat, 18 Jun 2011 06:57:39 -0700
- On a BN2 the fuel lines are also retained by the 'hairpin' style clips, though they're slightly different than the brake line clips. BCS is the only place I know of that has the correct fuel line cli
- /html/healeys/2011-06/msg00535.html (10,682 bytes)
- 6. Re: [Healeys] BN1/2 Boot Floor Holes (score: 1)
- Author: "Tracy Drummond" <bighealey@charter.net>
- Date: Sat, 18 Jun 2011 07:02:12 -0700
- I failed Gary's spelling test give me a Brake !! Pleze! Warm Regards, Tracy Drummond PMP | ITIL Service Manager | CISSP | bighealey@charter.net | 408-394-3444 cell | 408-776-0133 home | http://www.li
- /html/healeys/2011-06/msg00536.html (11,036 bytes)
- 7. Re: [Healeys] BN1/2 Boot Floor Holes (score: 1)
- Author: Bob Spidell <bspidell@comcast.net>
- Date: Sat, 18 Jun 2011 07:41:23 -0700
- Forgot to mention the battery line runs along the bottom of the passenger (LHD) side rail, and uses P-clips with sheetmetal screws like the wire harness. There's a welded-in nut on the passenger side
- /html/healeys/2011-06/msg00537.html (8,437 bytes)
- 8. Re: [Healeys] BN1/2 Boot Floor Holes (score: 1)
- Author: Barrie Robinson <barrie@look.ca>
- Date: Sat, 18 Jun 2011 14:38:51 -0400
- My BJ8 had 15,000 miles on it when I started work on it in 1985. If I remember correctly all the holes on the chassis/bulkhead had rubber plugs which had turned into rigid plastic!! I will look at m
- /html/healeys/2011-06/msg00543.html (12,528 bytes)
- 9. Re: [Healeys] BN1/2 Boot Floor Holes (score: 1)
- Author: Michael MacLean <rrengineer.mike@att.net>
- Date: Sat, 18 Jun 2011 14:34:26 -0700 (PDT)
- I have sprayed inner frame seal from Eastwood to as much of the inside of the frame rails as I could get to. It is like a zinc oxide (green color) with a rust encapsulator. Should be enough. Mike Mac
- /html/healeys/2011-06/msg00548.html (8,389 bytes)
This search system is powered by
Namazu