british-cars
[Top] [All Lists]

Re: [British-cars] are these lists still alive ?

To: <British-cars@autox.team.net>
Subject: Re: [British-cars] are these lists still alive ?
From: "Ron L'Herault" <lherault@bu.edu>
Date: Wed, 17 Mar 2010 08:56:28 -0400
I'm only an R and R mechanic, so maybe it is impossible, but if you have the
machine shop tools and skills, might it not be easier/quicker/less
"butchering" to make something that would allow you to mate the MG motor to
the Singer drive train?

-----Original Message-----
From: british-cars-bounces@autox.team.net
[mailto:british-cars-bounces@autox.team.net] On Behalf Of Mike Rambour
Sent: Tuesday, March 16, 2010 10:42 PM
To: british-cars@autox.team.net; british-cars-pre-war@autox.team.net
Subject: [British-cars] are these lists still alive ?

 I have a question about my 1934 Singer, I have very serious concerns 
about the motor and I am considering a temporary engine swap.  The 
Singer is a 6cylinder 1.5litre car, I have free access to a late 1960's 
or extremely early 1970's MGB that is pretty much a running rust bucket 
parts donor.  I am going to assume that its a 1800cc motor but anyone 
know the weight of the motor also motor and trans ?

 The Singer wheel track is 4'4" front and rear and according to the 
internet the MGB is 4.125 for the rear, I would have to put the Singer's 
18" wire wheels on the MGB's rear axle.  Would that track difference be 
a issue on the handling of the car ? since its wire wheels I am not sure 
I could put in spacers like you would on a steel rims.

 My thinking is to butcher this extremely rare 1934 Singer and put in 
the MGB drivetrain while I get the Singer motor redone, that will take 
some serious cash, the block is cracked, I have to have pistons made, 
babbitt bearings poured and its all going to be very expensive.  I would 
not want to do any permanent butchering of the Singer, anything and 
everything I do would have to be reversable when I finish the proper 
motor but it gets it on the road for now.

 Both rear ends are leaf springs so I don't see a issue there, the 
engine compartment is quite roomy for the 6 cylinder so the MG 4 should 
fit very nicely (not measured anything yet), I could weld up motor 
mounts that minimize the damage to the Singer or better yet do no 
damage.  The only "gotcha" I have at this time would be the clutch and 
brake pedal assembly and mixing the MG rear brakes with the Singer front 
brakes, I have to check on that as I don't even like the sound of it, 
but I should be able to take the MG front axle back plates and put them 
on the Singer, so I am back to just the pedal assembly without damaging 
the Singer chassis.

 I have all the cool toys to do this with, lathe, mill, welders, etc.  I 
just don't have the engine/drivetrain switching knowledge, never done 
that YET but it does not look too hard.  Well I have started it on 
another car but its not finished yet.

    mike
_______________________________________________
British-cars@autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation  $11.47
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage:
http://autox.team.net/mailman/options/british-cars/lherault@bu.edu
_______________________________________________
British-cars@autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation  $11.47
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums

<Prev in Thread] Current Thread [Next in Thread>