fot
[Top] [All Lists]

Re: [Fot] Intake/Exhaust manifold gasket

To: fot@autox.team.net
Subject: Re: [Fot] Intake/Exhaust manifold gasket
From: Tony Drews via Fot <fot@autox.team.net>
Date: Tue, 2 Feb 2021 15:06:10 -0600
Delivered-to: mharc@autox.team.net
Delivered-to: fot@autox.team.net
References: <1612296818.3uvtn92yow0kokw4@webmail.lumos.net> <BL0PR04MB452915E08BC82022AD237E64B4B59@BL0PR04MB4529.namprd04.prod.outlook.com>
User-agent: Mozilla/5.0 (Windows NT 10.0; Win64; x64; rv:78.0) Gecko/20100101 Thunderbird/78.7.0
I use Remflex in my TR-4 because I need the gap sealing 
characteristics.  I make my  own from sheet material they sell because 
the intake manifold holes on the pre-cut ones are too large for my use.  
However they are NOT reusable.

Regards, Tony Drews

On 2/2/2021 2:42 PM, Michael Moore via Fot wrote:
> I have not had those problems with the high-performance set, but I donâ??t 
> reuse them.
>
> I have not used Remflex, the they say they can be reused. But they are not 
> cheap, thatâ??s why I but a lot of the one Moss sells.
>
> http://catalog.remflex.com/TRIUMPH_Exhaust_Gasket_p/20-001.htm
>
>
> Thanks
> Mike
>
> Michael T. Moore, CPA
> 3255 West 26th Street
> Erie, PA 16506
>
> Phone:  814-616-8652  ext 100
> Fax:        888-865-5279
> Email:    mmoore@mtmcpafirm.com
>
> This electronic mail message contains confidential and legally privileged 
> information intended only for the use of the recipient. If the reader of this 
> message is not the intended recipient, the reader is hereby notified that any 
> dissemination, distribution, copying or other use of this message is strictly 
> prohibited and is hereby instructed to notify the sender immediately by 
> return email and destroy this copy of this message.
>
>
>
> -----Original Message-----
> From: Fot <fot-bounces@autox.team.net> On Behalf Of R. John Lye via Fot
> Sent: Tuesday, February 2, 2021 3:14 PM
> To: fot@autox.team.net
> Subject: [Fot] Intake/Exhaust manifold gasket
>
> Hi all,
>
> I have recently had to install and remove a header several times for my 
> TR-3A, and discovered that the Moss Motors "high performance" intake/exhaust 
> manifold gasket had disintegrated, despite not having even started the engine 
> yet.  So, I am looking for suggestions for a better solution.  Any thoughts 
> or suggestions?
> Thanks in advance.
>   
>
> --
> Thanks,
> John
>
> rjl6n@cstone.net
> _______________________________________________
> fot@autox.team.net
>
> http://www.fot-racing.com
>
> Donate: http://www.team.net/donate.html
> Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
> Unsubscribe/Manage: 
> http://autox.team.net/mailman/options/fot/mmoore@mtmcpafirm.com
>
>
> _______________________________________________
> fot@autox.team.net
>
> http://www.fot-racing.com
>
> Donate: http://www.team.net/donate.html
> Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
> Unsubscribe/Manage: 
> http://autox.team.net/mailman/options/fot/tony@tonydrews.com
>
>
_______________________________________________
fot@autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
Unsubscribe/Manage: 
http://autox.team.net/mailman/options/fot/mharc@autox.team.net


<Prev in Thread] Current Thread [Next in Thread>