healeys
[Top] [All Lists]

Re: knuckle busting OVERDRIVE/tranny drain plug

To: ahpowered@hotmail.com, healey.nut@gmail.com
Subject: Re: knuckle busting OVERDRIVE/tranny drain plug
From: "WILLIAM B LAWRENCE" <ynotink@msn.com>
Date: Fri, 16 Feb 2007 00:47:15 +0000
The ODs on the BN1s used a plug with a large hex cast in. Part #866-250 from 
Moss. Kind of pricy at $74.95.

Bill Lawrence


>From: "scott willis" <ahpowered@hotmail.com>
>Reply-To: "scott willis" <ahpowered@hotmail.com>
>To: healey.nut@gmail.com
>CC: healeys@autox.team.net
>Subject: Re: knuckle busting OVERDRIVE/tranny drain plug
>Date: Thu, 15 Feb 2007 08:22:28 -0600
>
>Now that looks good! Thanks Alan and all. I have a tool that is flat. It is 
>a wrench of sorts that is about 7 inches long with one tooth. It is not 
>good. I will try this or a plumbing device suggested.
>
>Cheers,
>
>Scott Willis
>Mashed 60 BN7 AH Club USA
>59 MGA
>66 E-Type FHC
>http://www.geocities.com/bgeuroclassics/BG_Euro.html
>BG Euro Classics Car Club President
>Bowling Green, KY
>
>
>
>
>
>>From: "Alan Seigrist Blue 100" <healey.nut@gmail.com>
>>To: "scott willis" <ahpowered@hotmail.com>
>>CC: healeys@autox.team.net
>>Subject: Re: knuckle busting OVERDRIVE/tranny drain plug
>>Date: Thu, 15 Feb 2007 17:13:56 +0800
>>
>>Scott -
>>
>>I don't know what tool you are using, but there is a special socket out
>>there for this cap and it works very well:
>>
>>See part number BT8 on this page:
>>
>>http://www.britishtool.com/servtool.htm
>>
>>http://www.britishtool.com/images/bt8lloyd.JPG
>>
>>It works just fine, and really the brass cap should not be on all that 
>>tight
>>anyway.
>>
>>Robb at Brit tool is a great guy and we should be thankful that this guy 
>>is
>>out there making these tools!
>>
>>Alan
>>
>>'52 A90
>>'53 BN1
>>'64 BJ8
>>
>>On 2/15/07, scott willis <ahpowered@hotmail.com> wrote:
>>>
>>>Sorry...I suppose it is the overdrive plug/cap on the bottom I am
>>>referring
>>>to. It is round and flat with notches around it. Any upgrades avail?
>>>
>>>Thanks,
>>>
>>>
>>>Scott Willis
>>>Mashed 60 BN7 AH Club USA
>>>59 MGA
>>>66 E-Type FHC
>>>http://www.geocities.com/bgeuroclassics/BG_Euro.html
>>>BG Euro Classics Car Club President
>>>Bowling Green, KY
>>>
>>>
>>>
>>>
>>>
>>> >From: "scott willis" <ahpowered@hotmail.com>
>>> >Reply-To: "scott willis" <ahpowered@hotmail.com>
>>> >To: healeys@autox.team.net
>>> >Subject: knuckle busting tranny drain plug Date: Wed, 14 Feb 2007
>>>21:56:25
>>> >-0600
>>> >
>>> >Hey folks,
>>> >
>>> >Anyone know of an upgrade for the BN7 3000 tranny drain plug? This
>>>notched
>>> >screw on plug is a horrid knuckle buster. The tool I have slips off
>>>nicely
>>> >as I try to tighten the thing. I would like a nut of some sort that I 
>>>can
>>> >use a crescent wrench on. Any advice on a better designed plug or a
>>>better
>>> >tool that will stay on when you push hard?
>>> >
>>> >Cheers,
>>> >
>>> >
>>> >Scott Willis
>>> >Mashed 60 BN7 AH Club USA
>>> >59 MGA
>>> >66 E-Type FHC
>>> >http://www.geocities.com/bgeuroclassics/BG_Euro.html
>>> >BG Euro Classics Car Club President
>>> >Bowling Green, KY




<Prev in Thread] Current Thread [Next in Thread>