healeys
[Top] [All Lists]

[Healeys] Apron Panel Set

Subject: [Healeys] Apron Panel Set
From: richchrysler at quickclic.net (Rich C)
Date: Fri, 12 Aug 2011 14:31:55 -0400
References: <BLU166-ds215E34AA77D506D4FD970FB3250@phx.gbl> <BAY166-W18D70E20366D8143D328EEA5250@phx.gbl> <95C627B8-9CE0-46D0-942B-E66096A06D0E@comcast.net>
Rob, 

Yes, the horizontal panel is there to help direct air into the radiator. It
also helps to tie in and stiffen the large area of otherwise unsupported
metal from the top of the shroud lip at the bonnet opening  all the way down
to the pair of frame mounting irons at the bottom of the shroud. 

The grille needs to be removed by simply undoing the 5 nuts and special
washers from the 5 studs across the top inner lip accessed from behind. With
these 5 removed, press down slightly and pull the grille assembly forward
from the top and then up from the bottom. Don't let the 5 studs catch the
painted upper edge of the grille opening.

The horizontal panel has notches to fit over the horn mounting bolts at the
back edge of the panel, so loosen the horn mounting bolts to allow the
notched flange to sandwich between the horn base and the cross member. At
the front edge there are two countersunk Phillips head 10-32 screws that
pass from shroud lower grille opening flange, through the apron, and are
fastened there with flat washers, lock washers and nuts. In addition the two
large vertical locating pegs in the bottom of the grill pass through a pair
of locating holes in this horizontal panel.

The horizontal panel is completely above all steering arms. The stator tube
wiring cable comes out of the bottom of the steering box and loops back and
down through a rubber grommet in the back corner of the apron where the
harness continues to anchor with a P clip to the front face of the frame
front cross member and finally plugs into it's appropriate connectors. 
 
The vertical dorsal panel mounts at the top with a single 10-32 Phillips
screw with flat washers, lock washer and nut to the upper inner cross brace
that also anchors the bonnet lip. At the bottom of the vertical dorsal
panel, the horizontal flange has two holes to fit 10-32 screws with flat
washers, lock washers and nuts. 

-----Original Message-----
From: healeys-bounces at autox.team.net [mailto:healeys-bounces at 
autox.team.net]
On Behalf Of robert westcott
Sent: 2011-08-12 12:01
To: healeys at autox.team.net
Subject: Re: [Healeys] Apron Panel Set

Never had one in my '55 and bought a replacement but still can't  
figure out how to get the thing in there. Do you need to remove the  
grill?
what is the sequence, horizontal panel and then add the vertical?  The  
steering linkage, horns and everything else seems to be in the way.
I can see why the PO left it out.
Is it really necessary for cooling or is it just cosmetic?

Rob Westcott

On Aug 11, 2011, at 11:16 PM, WILLIAM B LAWRENCE wrote:

> The way I heard it Donald didn't like being able to look through the  
> wheel
> wells from side to side and so put the vertical panel in as a visual  
> break.
>
> Bill Lawrence
>
>> From: gbrierton at hotmail.com
>> To: healeys at autox.team.net
>> Date: Thu, 11 Aug 2011 23:58:23 -0400
>> Subject: [Healeys] Apron Panel Set
>>
>> What was the function of the vertical panel?
>> GaryB
_______________________________________________
Healeys at autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation  $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage:
http://autox.team.net/mailman/options/healeys/richchrysler at quickclic.net

[demime 1.01d removed an attachment of type image/jpeg which had a name of 
Galvin BN1-190.jpg]

<Prev in Thread] Current Thread [Next in Thread>