healeys
[Top] [All Lists]

[Healeys] Master cylinder-Metric?

Subject: [Healeys] Master cylinder-Metric?
From: mgcharlie at comcast.net (Charlie Baldwin)
Date: Mon, 07 Nov 2011 14:40:18 -0500
References: <COL121-W63AE05834C42846BA72414A4DB0@phx.gbl> <E8870F10-2AD8-4829-883F-79D6CA17A256@sbcglobal.net> <707016B19766437E8E93AC443D1E41C0@AlanPC> <4EB825BA.8090602@chello.nl>
I have owned a few vintage Volvos (pre-early '70s) and they had mostly 
UNC threads with standard (to Americans) inch bolt heads.  These Volvos 
used Girling brakes in many cases and SU carbs.  Where they used ATE 
brakes and Bosch electrical components, they were metric.  Bodies, 
engines, gearboxes, rear axles, etc. were all UNC.  Many of the rear 
axles were by Dana, with similar ones used in Studebakers and Sunbeams.  
The earliest 1800s, of course, were built in the UK.
Charlie

On 11/7/2011 1:38 PM, Oudesluys wrote:
> Lotus is one of the exceptions as they used metric in their own 
> engines from the 907 engine. Do not know if they used metric in the 
> bodies.
> Of course a Continental Europe (Renault France) produced engine had 
> metric threads. Even long before the war there were very few 
> exceptions to that.
> Saab used a Triumph engine so I presume that the threads on those 
> engines are not metric, however if these were produced in licence by 
> Saab they might. Also Volvo may have used some UNF threads I believe.
> Kees Oudesluijs
> NL
>
>
> Op 7-11-2011 19:00, Alan Grossman schreef:
>> Renault powered Lotus Europa? Just askin'
>>
>> Cheers, Alan
>> ----- Original Message ----- From: "David Nock" 
>> <healeydoc at sbcglobal.net>
>> To: "Richard Kahn" <tahoehealey at hotmail.com>
>> Cc: <healeys at autox.team.net>
>> Sent: Monday, November 07, 2011 8:10 AM
>> Subject: Re: [Healeys] Master cylinder-Metric?
>>
>>
>>> NO British cars used Metrics until the Jaguars  in the mid 80s.
>>>
>>>
>>>
>>>
>>>
>>> David Nock
>>> British Car Specialists
>>> Stockton Ca 95205
>>> 209-948-8767
>>>
>>> www.britishcarspecialists.com
>>> .
>>> .
>>>
>>> On Nov 5, 2011, at 8:06 AM, Richard Kahn wrote:
>>>
>>>> Are the fittings for the brake and clutch master cylinder metric? I
>>>> bought a
>>>> bench bleeding kit from Napa that does not fit. They figured that a
>>>> British
>>>> car would have metric.  One more delay with another trip to the
>>>> store. I'll
>>>> have to bring the old unit in for sizing.
>>>> Rich Kahn
>>>> _______________________________________________
>>>> Healeys at autox.team.net
>>>> Donate: http://www.team.net/donate.html
>>>> Suggested annual donation  $12.75
>>>> Archive: http://www.team.net/archive
>>>> Forums: http://www.team.net/forums
>>>> Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/
>>>> healeydoc at sbcglobal.net
>>> _______________________________________________
>>> Healeys at autox.team.net
>>> Donate: http://www.team.net/donate.html
>>> Suggested annual donation  $12.75
>>> Archive: http://www.team.net/archive
>>> Forums: http://www.team.net/forums
>>> Unsubscribe/Manage: 
>>> http://autox.team.net/mailman/options/healeys/agrossman at pacific.net 
>> _______________________________________________
>> Healeys at autox.team.net
>> Donate: http://www.team.net/donate.html
>> Suggested annual donation  $12.75
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe/Manage: 
>> http://autox.team.net/mailman/options/healeys/coudesluijs at chello.nl
>>
>>
>> -----
>> Geen virus gevonden in dit bericht.
>> Gecontroleerd door AVG - www.avg.com
>> Versie: 2012.0.1869 / Virusdatabase: 2092/4602 - datum van uitgifte: 
>> 11/07/11
> _______________________________________________
> Healeys at autox.team.net
> Donate: http://www.team.net/donate.html
> Suggested annual donation  $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage: 
> http://autox.team.net/mailman/options/healeys/mgcharlie at comcast.net

[demime 1.01d removed an attachment of type text/x-vcard which had a name of 
mgcharlie.vcf]

<Prev in Thread] Current Thread [Next in Thread>