--===============9066301961966447332==
boundary="----=_Part_6001960_612805369.1436790960745"
------=_Part_6001960_612805369.1436790960745
Content-Transfer-Encoding: quoted-printable
I too ...am considering replacing brake/clutch hoses with Goodridge=C2=A0 s=
tainless hoses.and of course get rid of old fluid with new dot5 fluid (it h=
as dot5 in the system now)=C2=A0 brake m/c is good..................1966 BJ=
8..............any tips, problems, etc.=C2=A0=C2=A0=C2=A0 that I may encoun=
ter?=C2=A0=C2=A0 time is a big factor as I am going to ENCLAVE=20
=C2=A0=20
Mitch=20
----- Original Message -----
From: "I Erbs" <eyera3000@gmail.com>=20
To: "philip fish" <philipfish@waitrose.com>=20
Cc: "Ahealey help" <healeys@autox.team.net>=20
Sent: Monday, July 13, 2015 3:18:11 AM=20
Subject: Re: [Healeys] Replacing brake master cylinder, fluid reservoir and=
flexible brake pipes - what order?=20
I would use a baster to suck as much fluid out of the reservoir. Be careful=
, brake fluid can eat your paint. Then open up all four brake bleed screws.=
Good time to flush your system. Yes bench bleed MC.=20
Keep track of any shims between Mc and firewall.=20
Keep everything clean and use latex=C2=A0 gloves.=C2=A0 Check to be sure pu=
shrod pin loop is not elongated, as the wear out.=20
Be sure to open up slave cyl. Too to remove old fluid from clutch=20
Mr. Ira Erbs=20
On Jul 12, 2015 9:44 PM, "philip fish" < philipfish@waitrose.com > wrote:=
=20
Hi All,=20
This week I am going to replace the brake master cylinder, fluid reservoir =
and flexible brake pipes on my BT7. What is the best order to do these thre=
e steps?=20
Reservoir, flexible brake pipes, master cylinder is the route I was going t=
o take.=20
Will I need to bench bleed the MC?=20
Do I need to make any adjustments to the brakes before the bleeding step?=
=20
Should I drain all the fluid out of the system before replacing the reservo=
ir?=20
Any advice welcome.=20
Phil=20
_______________________________________________=20
Archive: http://www.team.net/archive=20
Healeys@autox.team.net=20
http://autox.team.net/mailman/listinfo/healeys=20
@gmail.com=20
_______________________________________________=20
Archive: http://www.team.net/archive=20
Healeys@autox.team.net=20
http://autox.team.net/mailman/listinfo/healeys=20
comcast.net=20
------=_Part_6001960_612805369.1436790960745
Content-Transfer-Encoding: quoted-printable
<html><body><div style=3D"font-family: Arial; font-size: 12pt; color: #0000=
00"><DIV>I too ...am considering replacing brake/clutch hoses with Goodridg=
e stainless hoses.and of course get rid of old fluid with new dot5 fl=
uid (it has dot5 in the system now) brake m/c is good................=
..1966 BJ8..............any tips, problems, etc. that I m=
ay encounter? time is a big factor as I am going to ENCLAVE<BR>=
</DIV>
<DIV> </DIV>
<DIV>Mitch</DIV>
<DIV><BR></DIV>
<HR id=3Dzwchr>
<DIV style=3D"FONT-SIZE: 12pt; TEXT-DECORATION: none; FONT-FAMILY: Helvetic=
a,Arial,sans-serif; FONT-WEIGHT: normal; COLOR: #000; FONT-STYLE: normal"><=
B>From: </B>"I Erbs" <eyera3000@gmail.com><BR><B>To: </B>"philip fish=
" <philipfish@waitrose.com><BR><B>Cc: </B>"Ahealey help" <healeys@=
autox.team.net><BR><B>Sent: </B>Monday, July 13, 2015 3:18:11 AM<BR><B>S=
ubject: </B>Re: [Healeys] Replacing brake master cylinder, fluid reservoir =
and flexible brake pipes - what order?<BR>
<DIV><BR></DIV>
<P dir=3Dltr>I would use a baster to suck as much fluid out of the reservoi=
r. Be careful, brake fluid can eat your paint. Then open up all four brake =
bleed screws. Good time to flush your system. Yes bench bleed MC.<BR>Keep t=
rack of any shims between Mc and firewall.<BR>Keep everything clean and use=
latex gloves. Check to be sure pushrod pin loop is not elongat=
ed, as the wear out.<BR>Be sure to open up slave cyl. Too to remove old flu=
id from clutch</P>
<P dir=3Dltr>Mr. Ira Erbs</P>
<DIV class=3Dgmail_quote>On Jul 12, 2015 9:44 PM, "philip fish" <<A href=
=3D"mailto:philipfish@waitrose.com"; target=3D_blank>philipfish@waitrose.com=
</A>> wrote:<BR>
<BLOCKQUOTE class=3Dgmail_quote style=3D"PADDING-LEFT: 1ex; MARGIN: 0px 0px=
0px 0.8ex; BORDER-LEFT: #ccc 1px solid">
<DIV style=3D"WORD-WRAP: break-word; FONT-SIZE: 16px; FONT-FAMILY: Calibri,=
sans-serif; COLOR: rgb(0,0,0)">
<DIV>Hi All,<BR>
<DIV><BR></DIV></DIV>
<DIV>This week I am going to replace the brake master cylinder, fluid reser=
voir and flexible brake pipes on my BT7. What is the best order to do these=
three steps?<BR>
<DIV><BR></DIV>Reservoir, flexible brake pipes, master cylinder is the rout=
e I was going to take. <BR>
<DIV><BR></DIV>Will I need to bench bleed the MC?<BR>Do I need to make any =
adjustments to the brakes before the bleeding step?<BR>Should I drain all t=
he fluid out of the system before replacing the reservoir?<BR>Any advice we=
lcome.<BR>Phil</DIV></DIV><BR>_____________________________________________=
__<BR>Support Team.Net <A href=3D"http://www.team.net/donate.html"; rel=3Dno=
referrer target=3D_blank>http://www.team.net/donate.html</A><BR>Suggested a=
nnual donation $12.75<BR>Archive: <A href=3D"http://www.team.net/arch=
ive" rel=3Dnoreferrer target=3D_blank>http://www.team.net/archive</A><BR>Fo=
rums: <A href=3D"http://www.team.net/forums"; rel=3Dnoreferrer target=3D_bla=
nk>http://www.team.net/forums</A><BR><BR><A href=3D"mailto:Healeys@autox.te=
am.net" target=3D_blank>Healeys@autox.team.net</A><BR><A href=3D"http://aut=
ox.team.net/mailman/listinfo/healeys" rel=3Dnoreferrer target=3D_blank>http=
://autox.team.net/mailman/listinfo/healeys</A><BR><BR>Unsubscribe/Manage: <=
A href=3D"http://autox.team.net/mailman/options/healeys/eyera3000@gmail.com=
" rel=3Dnoreferrer target=3D_blank>http://autox.team.net/mailman/options/he=
aleys/eyera3000@gmail.com</A><BR><BR><BR></BLOCKQUOTE></DIV><BR>___________=
____________________________________<BR>Support Team.Net http://www.team.ne=
t/donate.html<BR>Suggested annual donation $12.75<BR>Archive: http://=
www.team.net/archive<BR>Forums: http://www.team.net/forums<BR>
<DIV><BR></DIV>Healeys@autox.team.net<BR>http://autox.team.net/mailman/list=
info/healeys<BR>
<DIV><BR></DIV>Unsubscribe/Manage: http://autox.team.net/mailman/options/he=
aleys/dayton21@comcast.net<BR>
<DIV><BR></DIV></DIV>
<DIV><BR></DIV></div></body></html>
------=_Part_6001960_612805369.1436790960745--
--===============9066301961966447332==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============9066301961966447332==--
|