--===============1581660510585273908==
Content-Language: en-US
boundary="_000_DM6PR07MB45381722E8B25F004E3C2D12A5C70DM6PR07MB4538namp_"
--_000_DM6PR07MB45381722E8B25F004E3C2D12A5C70DM6PR07MB4538namp_
Content-Transfer-Encoding: quoted-printable
There are harness branches that diverge from the junction at the large grom=
met on the firewall. one extends forward on the left side down the chassis =
reinforcement and serves the front lighting, the turn signal relay and the =
connection of the turn signal switch and horn power at the bottom of the st=
eering column. The other extends forward down the right side and connects t=
o the generator (Yellow and Yellow/Green), ignition coil and distributor (W=
hite/Black).
The rear lighting harness connects below the junction and extends to the re=
ar along the left frame rail. That harness includes White/Green and White/B=
rown wires for turn signals, a Red wire for the tail and license plate ligh=
ts, a Green/Brown wire for the fuel level sensor, a White wire for fuel pum=
p power and a White/Black wire for the ignition grounding (kill) switch. Yo=
u should find matching wires in the main harness. It's just a matter of mat=
ching wire colors and snapping the appropriate bullet connectors together. =
I had a problem with mine in that I had to find some extra slack to keep th=
e connectors from pulling loose.
Bill Lawrence
BN1 #554
________________________________
From: Healeys <healeys-bounces@autox.team.net> on behalf of Per Schoerner <=
per@schoerner.se>
Sent: Friday, November 9, 2018 8:28:36 PM
To: healeys@autox.team.net
Subject: Re: [Healeys] Questions of the day
FWIW, looking at a wiring scheme for a 100/6 there is one group of 4
cables that fit into the steering column, three green wires, two of them
with markings, and one brown with black.
Then there is one group of three blue cables, again two of them with
markings, that is for the dip switch.
Then there is a loooong harness for the rear of the car, that attach to
the main harness in front of the firewall to the left of the engine.
I would expect that there is a similar setup for your BN2(?).
Hope this helps a little.
Per
Den 2018-11-09 kl. 19:37, skrev Michael MacLean:
> I have been sitting here for a few hours trying to label wires of this
> loom. I think I have the instrument panel pretty much done. Wire color
> code and location on the main harness works good together. Beyond that
> I am pulling my hair out. Not having an old harness on the car as I
> bought it, I have no idea where these other four sub harnesses locate on
> the car. I am sure one or more of the sub harnesses plug into the main
> harness, but I can't find any group of wire colors that match groups of
> wires on the main harness. I'll be lucky if there is no smoke when I
> turn the key the first time.
> Mike M
>
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archiv=
e
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
sn.com
--_000_DM6PR07MB45381722E8B25F004E3C2D12A5C70DM6PR07MB4538namp_
Content-Transfer-Encoding: quoted-printable
<html>
<head>
<meta http-equiv=3D"Content-Type" content=3D"text/html; charset=3Dus-ascii"=
>
<style type=3D"text/css" style=3D"display:none;"><!-- P {margin-top:0;margi=
n-bottom:0;} --></style>
</head>
<body dir=3D"ltr">
<div id=3D"divtagdefaultwrapper" style=3D"font-size:12pt;color:#000000;font=
-family:Calibri,Helvetica,sans-serif;" dir=3D"ltr">
<p style=3D"margin-top:0;margin-bottom:0">There are harness branches t=
hat diverge from the junction at the large grommet on the firewall. one ext=
ends forward on the left side down the chassis reinforcement and serves the=
front lighting, the turn signal relay
and the connection of the turn signal switch and horn power at the bo=
ttom of the steering column. The other extends forward down the right side =
and connects to the generator (Yellow and Yellow/Green), ignition coil=
and distributor (White/Black). </p>
<p style=3D"margin-top:0;margin-bottom:0"><br>
</p>
<p style=3D"margin-top:0;margin-bottom:0">The rear lighting harness co=
nnects below the junction and extends to the rear along the left frame=
rail. That harness includes White/Green and White/Brown wires for turn sig=
nals, a Red wire for the tail and license plate lights,
a Green/Brown wire for the fuel level sensor, a White wire for fuel p=
ump power and a White/Black wire for the ignition grounding (kill) switch. =
You should find matching wires in the main harness. It's just a matter of m=
atching wire colors and snapping the
appropriate bullet connectors together. I had a problem with mine in =
that I had to find some extra slack to keep the connectors from pulling loo=
se.</p>
<p style=3D"margin-top:0;margin-bottom:0"><br>
</p>
<p style=3D"margin-top:0;margin-bottom:0">Bill Lawrence</p>
<p style=3D"margin-top:0;margin-bottom:0">BN1 #554</p>
</div>
<hr style=3D"display:inline-block;width:98%" tabindex=3D"-1">
<div id=3D"divRplyFwdMsg" dir=3D"ltr"><font face=3D"Calibri, sans-serif" st=
yle=3D"font-size:11pt" color=3D"#000000"><b>From:</b> Healeys <healeys-b=
ounces@autox.team.net> on behalf of Per Schoerner <per@schoerner.se&g=
t;<br>
<b>Sent:</b> Friday, November 9, 2018 8:28:36 PM<br>
<b>To:</b> healeys@autox.team.net<br>
<b>Subject:</b> Re: [Healeys] Questions of the day</font>
<div> </div>
</div>
<div class=3D"BodyFragment"><font size=3D"2"><span style=3D"font-size:11pt;=
">
<div class=3D"PlainText">FWIW, looking at a wiring scheme for a 100/6 there=
is one group of 4
<br>
cables that fit into the steering column, three green wires, two of them <b=
r>
with markings, and one brown with black.<br>
Then there is one group of three blue cables, again two of them with <br>
markings, that is for the dip switch.<br>
Then there is a loooong harness for the rear of the car, that attach to <br=
>
the main harness in front of the firewall to the left of the engine.<br>
I would expect that there is a similar setup for your BN2(?).<br>
Hope this helps a little.<br>
<br>
Per<br>
<br>
Den 2018-11-09 kl. 19:37, skrev Michael MacLean:<br>
> I have been sitting here for a few hours trying to label wires of this=
<br>
> loom. I think I have the instrument panel pretty much done. =
; Wire color <br>
> code and location on the main harness works good together. Beyon=
d that <br>
> I am pulling my hair out. Not having an old harness on the car a=
s I <br>
> bought it, I have no idea where these other four sub harnesses locate =
on <br>
> the car. I am sure one or more of the sub harnesses plug into th=
e main <br>
> harness, but I can't find any group of wire colors that match groups o=
f <br>
> wires on the main harness. I'll be lucky if there is no smoke wh=
en I <br>
> turn the key the first time.<br>
> Mike M<br>
> <br>
_______________________________________________<br>
m.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/healeys";>http://www.team.=
net/pipermail/healeys</a>
<a href=3D"http://autox.team.net/archive";>http://autox.team.net/archive</a>=
<br>
<br>
Healeys@autox.team.net<br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys";>http://autox.tea=
m.net/mailman/listinfo/healeys</a><br>
<br>
s/ynotink@msn.com">
http://autox.team.net/mailman/options/healeys/ynotink@msn.com</a><br>
<br>
</div>
</span></font></div>
</body>
</html>
--_000_DM6PR07MB45381722E8B25F004E3C2D12A5C70DM6PR07MB4538namp_--
--===============1581660510585273908==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============1581660510585273908==--
|