--===============0725661724403223203==
--000000000000bd55c105b87a3e6b
Wrap the area where you want to cut tightly with a couple of layers of
masking tape then cut it slowy either with a cut off wheel or on the corner
of the wheel on a bench grinder.
Remember measure twice cut once.
M
On Sat., Jan. 9, 2021, 9:56 a.m. Leonard Berkowitz, <DrBerkowitz@hotmail.com>
wrote:
> I have just reinstalled the carburetors on my BJ7 after replacing the jet
> assemblies on both. I purchased new scuttle to carburetor choke lines.
> Which installed fairly easily. Only problem is that both are considerably
> longer than they need to be. That didn't present a problem for the rear
> carb but the choke wire on the front was hitting the horn and this
> interfered with the operation of the choke. I tried to cut the wire and it
> just unraveled and became unusable. Does anyone have a suggestion on how to
> shorten the wire before or after it is installed.
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
>
> Archive: http://www.team.net/pipermail/healeys
> http://autox.team.net/archive
>
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com
>
>
--000000000000bd55c105b87a3e6b
Content-Transfer-Encoding: quoted-printable
<div dir=3D"auto">Wrap the area where you want to cut tightly with a couple=
of layers of masking tape then cut it slowy either with a cut off wheel or=
on the corner of the wheel on a bench grinder.<div dir=3D"auto">Remember m=
easure twice cut once.</div><div dir=3D"auto"><br></div><div dir=3D"auto">M=
</div></div><br><div class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmail_=
attr">On Sat., Jan. 9, 2021, 9:56 a.m. Leonard Berkowitz, <<a href=3D"ma=
ilto:DrBerkowitz@hotmail.com">DrBerkowitz@hotmail.com</a>> wrote:<br></d=
iv><blockquote class=3D"gmail_quote" style=3D"margin:0 0 0 .8ex;border-left=
:1px #ccc solid;padding-left:1ex">
<div dir=3D"ltr">
<div style=3D"font-family:Calibri,Helvetica,sans-serif;font-size:12pt;color=
:rgb(0,0,0)">
I have just reinstalled the carburetors on my BJ7 after replacing the jet a=
ssemblies on both. I purchased new scuttle to carburetor choke lines. Which=
installed fairly easily. Only problem is that both are considerably longer=
than they need to be. That didn't
present a problem for the rear carb but the choke wire on the front was hi=
tting the horn and this interfered with the operation of the choke.=C2=A0 I=
tried to cut the wire and it just unraveled and became unusable. Does anyo=
ne have a suggestion on how to shorten
the wire before or after it is installed. =C2=A0</div>
</div>
_______________________________________________<br>
rer noreferrer" target=3D"_blank">http://www.team.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/healeys"; rel=3D"noreferre=
r noreferrer" target=3D"_blank">http://www.team.net/pipermail/healeys</a> <=
a href=3D"http://autox.team.net/archive"; rel=3D"noreferrer noreferrer" targ=
et=3D"_blank">http://autox.team.net/archive</a><br>
<br>
<a href=3D"mailto:Healeys@autox.team.net"; target=3D"_blank" rel=3D"noreferr=
er">Healeys@autox.team.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys"; rel=3D"noreferre=
r noreferrer" target=3D"_blank">http://autox.team.net/mailman/listinfo/heal=
eys</a><br>
<br>
s/michaelsalter@gmail.com" rel=3D"noreferrer noreferrer" target=3D"_blank">=
http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com</a><b=
r>
<br>
</blockquote></div>
--000000000000bd55c105b87a3e6b--
--===============0725661724403223203==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============0725661724403223203==--
|