shop-talk
[Top] [All Lists]

Re: New use for old table saw?

To: Bob Dicke <rtdengr@charter.net>,
Subject: Re: New use for old table saw?
From: Pat Horne <pjhorne@mail.utexas.edu>
Date: Fri, 25 Nov 2005 11:39:03 -0600

shop-talk supported in part by Fat Chance Garage
http://fatchancegarage.com

Bob,

I found the article, it was in the October 2000 issue of American 
Woodworker.

Article reprints can be purchased for $3.00 by calling (715) 246-4344or 
write to:

Copies
American Woodworker
Box 83695
Stillwater, MN 55083-0695

I will post a copy of this email to the list.

Peace,
Pat


Bob Dicke wrote:

>Pat
>
>I would be very interested in that article if you can still find it.
>
>Bob
>
>
>
>-----Original Message-----
>From: shop-talk-owner@autox.team.net [mailto:shop-talk-owner@autox.team.net]
>On Behalf Of Pat Horne
>Sent: Friday, November 25, 2005 9:19 AM
>To: PJ McGarvey
>Cc: shop-talk@autox.team.net
>Subject: Re: New use for old table saw?
>
>
>
>shop-talk supported in part by Fat Chance Garage
>http://fatchancegarage.com
>
>PJ,
>
>It took a few reads to see that you bought a new SAW, not a new MOTOR, 
>correct?
>
>As for a use for the old saw, there are a few. Depending on what size 
>jobs you do, and how big the saw table top is, you can convert it into a 
>router table, or just use it as is as an assembly table - if the top is 
>big enough.
>
>Old Rockwell saws are generally worth more in running condition than 
>either a router table, or assembly, so you might want to consider 
>putting a new motor on it and selling it, then buy or build a router 
>table with what you make on its sale.
>
>I built a table that is 2' wide and 6' long that has a replaceable  
>2'x2'  section in the middle. I built inserts for my router, sanding  
>table, thickness planer, and a blank top. I put slots across the bench 
>so that bar clamps can be put almost anywhere on the table to hold 
>things down, including the fence for the router.I also set its height to 
>be about 1/4" lower than my table saw table so it can be used as an out 
>feed or side table as needed. It has a torsion box in the bottom to keep 
>the top flat, no matter how far the floor is off. It's heavy, a bit over 
>200 lbs, but it was cheap. It's made out of 2 sheets of 3/4" MDF, so it 
>cost under $75 to build. I got the basic design out of a wood working 
>magazine several years ago. If folks are interested, I can scare up the 
>info on the article.
>
>PJ McGarvey wrote:
>
>  
>
>>shop-talk supported in part by Fat Chance Garage
>>http://fatchancegarage.com
>>
>>Thinking about whether to chuck the old Rockwell 'contractors' table 
>>saw I picked up awhile back for $15, motor was starting to make some 
>>bad vibrating noises, so I bought a new one.
>>
>>Since it has a decent top, mitre gauge, fence, etc, is there some 
>>other way I can use this big hunk of metal?  I was thinking maybe a 
>>router table, or something like that, but not sure on the details, 
>>probably just as easy to make my own router table.
>>
>>PJ
>>
>>
>>    
>>
>
>  
>

-- 
-- Support Habitat for Humanity - a hand UP, not a hand OUT --




<Prev in Thread] Current Thread [Next in Thread>