spridgets
[Top] [All Lists]

Re: [Spridgets] Fuel take carbon and vapor filters

To: "'Jack Laird'" <jlaird237@cox.net>, "'Bill L'"
Subject: Re: [Spridgets] Fuel take carbon and vapor filters
From: "Guy Weller" <guy.weller@tiscali.co.uk>
Date: Wed, 9 Jul 2008 13:38:17 +0100
--===============0492371443==
Content-Type: text/plain; charset="windows-1250"
Content-Transfer-Encoding: 7bit

Ahh!  Sorry, My comments about "reading" the Tach of course don't apply with
mechanical ones!

It could still be the valves binding if the clearances are a bit tight.

Guy

-----Original Message-----
From: Jack Laird [mailto:jlaird237@cox.net]
Sent: 09 July 2008 13:27
To: Guy Weller; 'Bill L'; 'Leo'
Cc: spridgets@autox.team.net
Subject: Re: [Spridgets] Fuel take carbon and vapor filters


It is a Bugeye, one maybe the nicest restoration I have seen. All orginal or
better. Mechanical tac, standard everything.


----- Original Message -----
From: "Guy Weller" <guy.weller@tiscali.co.uk>
To: "'Bill L'" <pythias@pacifier.com>; "'Leo'" <60bugeye@cebridge.net>
Cc: <spridgets@autox.team.net>
Sent: Wednesday, July 09, 2008 2:21 AM
Subject: Re: [Spridgets] Fuel take carbon and vapor filters


> Leo,
> If it is an electrical misfire then the tachometer needle will thrash
> around. If it is fuel / vapour lock etc then the revs will drop as it
> misfires but the needle won't thrash about so much.
> But it could be valves sticking as they get hot. Is it a standard camshaft
> and what clearance are you running the tappets at?
>
> Guy
>
> -----Original Message-----
> From: spridgets-bounces+guy.weller=tiscali.co.uk@autox.team.net
> [mailto:spridgets-bounces+guy.weller=tiscali.co.uk@autox.team.net]On
> Behalf
> Of Bill L
> Sent: 09 July 2008 05:08
> To: Leo
> Cc: spridgets@autox.team.net
> Subject: Re: [Spridgets] Fuel take carbon and vapor filters
>
>
> Hello Leo,
>
>     I too am leaning toward coil. 10 minutes shouldn't be long enough
>     to vapor lock it, I would think. however it is long enough for
>     the coil to heat up and start acting .... ODD...
>
>     and its an easy enough thing to check. Swap coils .. i've heard
>     of the coil being broken not enough to see right where the the
>     low tension leads connect.... .. ALSO .. CHANGE the CONDENSOR!
>     that too will cause similar problems, and the only way to check
>     it is to change it....
>
> --
> Best regards,
> Bill L.                           mailto:pythias@pacifier.com
>
> '66 Sprite MKIII HAN8L49403   "the red thing"
>
>  File not found. Should I fake it? (Y/N)
>


----------------------------------------------------------------------------
----


> _______________________________________________
> Support Team.Net  http://www.team.net/donate.html
>
> You are subscribed as jlaird237@cox.net
>
> http://www.team.net/archive
>
> http://autox.team.net/mailman/listinfo/spridgets
>


----------------------------------------------------------------------------
----



No virus found in this incoming message.
Checked by AVG.
Version: 8.0.100 / Virus Database: 270.4.6/1540 - Release Date: 7/8/2008
6:33 AM

--===============0492371443==
Content-Type: text/plain; charset="us-ascii"
MIME-Version: 1.0
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________
Support Team.Net  http://www.team.net/donate.html


http://www.team.net/archive

http://autox.team.net/mailman/listinfo/spridgets

--===============0492371443==--

<Prev in Thread] Current Thread [Next in Thread>