tigers
[Top] [All Lists]

Re: [Tigers] 3 gauges stopped working

To: allanballard@att.net, tkparker1941@gmail.com
Subject: Re: [Tigers] 3 gauges stopped working
From: CoolVT@aol.com
Date: Wed, 28 Jul 2010 12:12:25 EDT
Yup,  same problem and cure that I had.  
 
 
In a message dated 7/28/2010 11:54:08 A.M. Eastern Daylight Time,  
allanballard@att.net writes:

Mike,  everyone,

voila!  :)

One side of fuse box needed  "treatment" with a small file--now the gauges 
are
working  again...

Thanks,

Allan


On Jul 28, 2010, at 10:38 AM,  Tom Parker wrote:

> True. (I looked at the Mark 2 diagram).  Grounding is simple to check, 
so's
voltage. I suspect but don't know, that  a short in the stabilizer would 
awaken
the smoke gods or blow the  fuse.
>
> Anyhow, schedule the Chiropractor and take a look. A  jumper clipped to 
frame
ground and the back mounting stud of a gauge  verifies the grounding, a 
meter
verifies the voltage stabilizer. There's  always the possibility of multiple
failures (In electronics it's much more  common than one might think...), so
take it one gauge at a  time.
>
> God hunting, Allan!
>
> Tom
>
>  On Wed, Jul 28, 2010 at 10:21 AM, Smit, Theo  <Theo.Smit@dynastream.com>
wrote:
> The stabilizer only  regulates the fuel and temperature gauges (to 10 
volts
average); the tach  has its own internal regulation. However, a failure of 
the
stabilizer that  shorted the (green) circuit to ground would disable all  
three
gauges.
>
> Theo
>
> > -----Original  Message-----
> > From: tigers-bounces@autox.team.net  [mailto:tigers-
> > bounces@autox.team.net] On Behalf Of Tom  Parker
> > Sent: July 28, 2010 8:03 AM
> > To: Allan  Ballard
> > Cc: tigers@autox.team.net
> > Subject: Re:  [Tigers] 3 gauges stopped working
> >
> > There's a voltage  stabilizer behind the dash that's supposed to keep
> > the
>  > voltage constant at @ 12v (see the service manual for the exact
>  > voltage).
> > You might look at he voltage input on one of the  failing gauges with a
> > volt
> > meter and follow the  yellow brick road (wiring diagram) if the voltage
> > is
> >  missing or out of spec.
> >
> > Tom
>  >
>
>
>
----------------------------------------------------------------------------
-
---
>  This e-mail and any attachments may contain confidential material for  
the
sole use of the intended recipient. If you are not the intended  recipient,
please be aware that any disclosure, copying, distribution or  use of this
e-mail or any attachment is prohibited. If you have received  this e-mail in
error, please contact the sender and delete all  copies.
>
> Thank you for your  cooperation.
_______________________________________________
Tigers@autox.team.net
Donate:  http://www.team.net/donate.html
Archive:  http://www.team.net/archive
Forums:  http://www.team.net/forums
Unsubscribe/Manage:  
http://autox.team.net/mailman/options/tigers/coolvt@aol.com
_______________________________________________
Tigers@autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums

<Prev in Thread] Current Thread [Next in Thread>