triumphs
[Top] [All Lists]

Re: [TR] Overheatng

To: <terryrs@comcast.net>, "Triumphs" <triumphs@autox.team.net>
Subject: Re: [TR] Overheatng
From: "Skip Gurnee" <skip47@gbis.com>
Date: Fri, 24 Aug 2012 15:48:42 -0700
Delivered-to: triumphs-archive@autox.team.net
Delivered-to: triumphs@autox.team.net
In-reply-to: <342001455.938795.1345844485628.JavaMail.root@sz0059a.westchester.pa.mail.comcast.net>
List-archive: <http://autox.team.net/pipermail/triumphs>
List-help: <mailto:triumphs-request@autox.team.net?subject=help>
List-id: Triumph Sports car discussion <triumphs.autox.team.net>
List-post: <mailto:triumphs@autox.team.net>
List-subscribe: <http://autox.team.net/mailman/listinfo/triumphs>, <mailto:triumphs-request@autox.team.net?subject=subscribe>
List-unsubscribe: <http://autox.team.net/mailman/options/triumphs>, <mailto:triumphs-request@autox.team.net?subject=unsubscribe>
References: <342001455.938795.1345844485628.JavaMail.root@sz0059a.westchester.pa.mail.comcast.net>
Sender: triumphs-bounces@autox.team.net
One possibility that I've encountered is a misalignment of the two pulleys, like the alternator is cocked to one side, or in a different plane. You should be able to see it from the side. I like George's solutions, and I'm sure others will come up with more. I've had crank bearings go bad; they didn't squeal, and began to knock pretty quick. I doubt that's the problem, especially with the sound disappearing with cold water on the alternator.
Skip Gurnee  64 TR4, 65 TR4A
Nevada

-----Original Message----- From: terryrs@comcast.net
Sent: Friday, August 24, 2012 2:41 PM
To: Triumphs
Subject: [TR] Overheatng

History. Have about three thousand miles on the engine rebuild. When I started it the first time, there was intense squealing for a few seconds that then went way. I figured it for a dry water pump.

Squealing has returned. Sounds for all the world like a fan belt issue or a bad bearing on either the water pump or alternator. Tried the stethoscope, couldn't isolate, so swapped out the water pump. Squeal persisted. Stethoscoped the alternator again, couldn't isolate, but then accidently dropped cold water on the alternator and the sound stopped abruptly. What was THAT all about??

So, bought a new GM alternator, adapted it to fit, put the old wide-belt pulley on it, and reinstalled. Same squeal as before.

But in the past week, the engine is overheating at idle and in hot weather. I'm running the belt looser than I usually do, but watching the action, the pulleys all seem to be turning, but am wondering if they're not going as fast as they should and the squealing is slippage?

Will try belt dressing to see if that changes anything.

Question: If I was spinning a crank bearing, either main or rod, it would make much different noises than a belt squeal, right?

Terry Smith, '59 TR3A
New Hampshire

** triumphs@autox.team.net **

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage: 
http://autox.team.net/mailman/options/triumphs/triumphs-archive@autox.team.net

<Prev in Thread] Current Thread [Next in Thread>