[Shotimes] rod bearings

Ron Porter ronporter@prodigy.net
Tue, 29 Apr 2003 14:55:20 -0400 

Josh at SHO Nut also has the EGR gasket.

Ron Porter 

-----Original Message-----
From: shotimes-admin@autox.team.net [mailto:shotimes-admin@autox.team.net]
On Behalf Of Steve Tatro
Sent: Tuesday, April 29, 2003 2:36 PM
To: 'Paul L Fisher'
Cc: shotimes@autox.team.net
Subject: RE: [Shotimes] rod bearings


Do you just call Parts Voice for the gasket?  I can't find it in their
(very well done) part search.

Thanks.

Steve Tatro 
Red/Black '93 with 167k miles 
Cincinnati, Ohio 



-----Original Message-----
From: shotimes-admin@autox.team.net
[mailto:shotimes-admin@autox.team.net] On Behalf Of Paul L Fisher
Sent: Tuesday, April 29, 2003 2:15 PM
To: Kerry Kinion
Cc: shotimes@autox.team.net
Subject: Re: [Shotimes] rod bearings


Ohhh... Some other points as well. Some are covered on Kurt's web site,
some aren't.

1. The gasket from the oil pickup tube to the oil pump is discontinued
E9DZ-6626-A. You can get it from www.partsvoice.com or you can use an
EGR gasket.

2. The torque specs for the nut for the oil pickup tube MIGHT be wrong
in the Helms. I trusted it and ended up shearing off the stud. Luckily,
I could get a pair of vise-grips on it to get it out.

Paul L Fisher
'93 Ford Taurus SHO Crimson Clearcoat ATX 171K Build date 11/18/1992
- K&N Panel filter, Tokico Struts, Eibach Springs, Dynomax cat-back,
Holley 190lph fuel pump, FPS rebuilt ATX, 26mm rear sway bar,
Performance-Plus Stainless Steel Y-pipe, '96 brake upgrade,
Proportioning valve plugs, Delrin sub-frame bushings, Amsoil Series 2000
0W-30 oil, Amsoil Synthetic ATF.

SHO Club member http://www.shoclub.com/
Check out my web site http://www.paul-fisher.com/
Amsoil dealer http://www.paul-fisher.com/oil.htm

Get $5 free from Paypal! https://www.paypal.com/refer/pal=P3XEFFBFUFKN6

----- Original Message ----- 
From: "Paul L Fisher" <sho@paul-fisher.com>
To: <1badsho@mail.tnh.net>; "Kerry Kinion" <kerry@kinionfurniture.com>
Cc: <shotimes@autox.team.net>
Sent: Tuesday, April 29, 2003 1:04 PM
Subject: Re: [Shotimes] rod bearings


> If you do, make sure you only put it on the side that faces the crank,

> not the rod.
>
> Paul L Fisher
> '93 Ford Taurus SHO Crimson Clearcoat ATX 171K Build date 11/18/1992
> - K&N Panel filter, Tokico Struts, Eibach Springs, Dynomax cat-back,
Holley
> 190lph fuel pump, FPS rebuilt ATX, 26mm rear sway bar, 
> Performance-Plus Stainless Steel Y-pipe, '96 brake upgrade, 
> Proportioning valve plugs,
Delrin
> sub-frame bushings, Amsoil Series 2000 0W-30 oil, Amsoil Synthetic 
> ATF.
>
> SHO Club member http://www.shoclub.com/
> Check out my web site http://www.paul-fisher.com/
> Amsoil dealer http://www.paul-fisher.com/oil.htm
>
> Get $5 free from Paypal! 
> https://www.paypal.com/refer/pal=P3XEFFBFUFKN6
>
> ----- Original Message -----
> From: "Donelson Don" <1badsho@mail.tnh.net>
> To: "Kerry Kinion" <kerry@kinionfurniture.com>
> Cc: <shotimes@autox.team.net>
> Sent: Tuesday, April 29, 2003 11:38 AM
> Subject: RE: [Shotimes] rod bearings
>
>
> > havent read all the threads to this post but havent seen anyone 
> > mention
to
> use pre lube on all the new bearings ....
> >
> > Sorta of important !
> >
> > dond
> >
> > ---------- Original Message ----------------------------------
> > From: "Kerry Kinion" <kerry@kinionfurniture.com>
> > Date:  Tue, 29 Apr 2003 00:11:34 -0700
> >
> > >>>Don't worry about it.  I and many others on the list are the same

> > >>>way
> > >when we attempt to do something for the first time on our SHOs.  
> > >They are our babies, and we want to make sure we don't do anything 
> > >to screw them up!<<
> > >
> > >I know I'll get flamed again if I write anymore, but the sentence 
> > >above pretty much says it all as far as my work on my SHO goes.  
> > >Because of this kind of attitude and understanding of the car AND 
> > >willingness to help goes, I'll continue to pump money and time and 
> > >brain energy into
my
> > >SHO, just to keep it running and eventually add a few mods to the 
> > >car!
> > >
> > >Later,
> > >
> > >Kerry
> > >
> > >-----Original Message-----
> > >From: Josh Salaets [mailto:jsalaets@msn.com]
> > >Sent: Monday, April 28, 2003 11:57 PM
> > >To: Kerry Kinion; shotimes@autox.team.net
> > >Subject: Re: [Shotimes] rod bearings
> > >
> > >> Are non standard bearings not available?  I only had a short 
> > >> conversation w/my local NAPA dealer, but she seemed to think I 
> > >> could
> > >get
> > >> the non-standard sizes if needed.
> > >
> > >Yeah, the non-standard sizes are available last time I checked when

> > >I ordered my standard size rod bearings.  When I went to do mine, 
> > >Napa
was
> > >out
> > >of stock and said they couldn't get any in for about a month.  I 
> > >had to hunt all around Portland to find some at a place that didn't

> > >want to charge me a
> > >ton for them.
> > >
> > >> Sorry for all the stupid questions - but being as anal as I am, I
like
> > >> to know everything I can before I start wrenching!
> > >
> > >Don't worry about it.  I and many others on the list are the same 
> > >way when we attempt to do something for the first time on our SHOs.

> > >They are
our
> > >babies, and we want to make sure we don't do anything to screw them

> > >up!
> > >
> > >BTW, after Plastigauging the first journal and finding it was right

> > >in spec, I didn't bother on the other ones since it is kind of a 
> > >PITA and I was running out of time.  Obviously everything is okay, 
> > >since I took the
car
> > >out
> > >to PIR right after finishing the job and raced it all day.  15,000
miles
> > >and
> > >no problems.  Even the oil analyses I've sent in look excellent!
> > >
> > >In your case, I would probably Plastigauge them all, since you can 
> > >actually hear them knocking - something I didn't.  I would have 
> > >checked the tolerances on all of them if I wasn't running short on 
> > >time.
> > >
> > >Josh Salaets
> > >95 SHO MTX (See it at: www.cardomain.com/id/sh0gun)
> > >85 Omni GLH-T (Yeah, it's fast)
> > >NWSHOC Member
> > >Aloha (Portland), OR 
> > >_______________________________________________
> > >Shotimes mailing list
> > >Shotimes@autox.team.net 
> > >http://www.team.net/mailman/listinfo/shotimes
> > _______________________________________________
> > Shotimes mailing list
> > Shotimes@autox.team.net 
> > http://www.team.net/mailman/listinfo/shotimes
>
>
> ---
> Outgoing mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.476 / Virus Database: 273 - Release Date: 4/24/2003
>


---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.476 / Virus Database: 273 - Release Date: 4/24/2003
_______________________________________________
Shotimes mailing list
Shotimes@autox.team.net http://www.team.net/mailman/listinfo/shotimes
_______________________________________________
Shotimes mailing list
Shotimes@autox.team.net
http://www.team.net/mailman/listinfo/shotimes