[Shotimes] Brake Bias Plugs

[Paul L Fisher]

I don't think I would trust not welding it. The material you will be putting
on the holes will be taking the few thousand PSI of the brake fluid when you
slam on the brakes. If there were a catastrophic failure of the plug, you
will be pumping large amounts of fluid onto the ground.

Paul L Fisher
'93 Ford Taurus SHO Crimson Clearcoat ATX 171K Build date 11/18/1992
- K&N Panel filter, Tokico Struts, Eibach Springs, Dynomax cat-back, Holley
190lph fuel pump, FPS rebuilt ATX, 26mm rear sway bar, Performance-Plus
Stainless Steel Y-pipe, '96 brake upgrade, Proportioning valve plugs, Delrin
sub-frame bushings, Amsoil Series 2000 0W-30 oil, Amsoil Synthetic ATF.
'00 Ford Explorer XLT 5.0L V8 AWD Oxford White Clearcoat 41K Build date
11/19/1999
- Amsoil Series 2000 0W-30 oil, K&N Fuel Injection Performance Kit

SHO Club member http://www.shoclub.com/
Check out my web site http://www.paul-fisher.com/
Amsoil dealer http://www.paul-fisher.com/oil.htm

Get $5 free from Paypal! https://www.paypal.com/refer/pal=P3XEFFBFUFKN6

----- Original Message -----
From: "Bruce Malachuk" <bmalach1@nycap.rr.com>
To: "Midwest SHO Specialists" <SHOtimes@midwestsho.com>; "SHOtimes"
<shotimes@autox.team.net>
Sent: Friday, March 07, 2003 11:43 PM
Subject: Re: [Shotimes] Brake Bias Plugs


> well if I had a welder that that would be easy and I wouldn't have asked.
>
> ----- Original Message -----
> From: "Midwest SHO Specialists" <SHOtimes@midwestsho.com>
> To: "Bruce Malachuk" <bmalach1@nycap.rr.com>; "SHOtimes"
> <shotimes@autox.team.net>
> Sent: Saturday, March 08, 2003 12:35 AM
> Subject: Re: [Shotimes] Brake Bias Plugs
>
>
> > Not to oversimplify things Bruce, but you can remove your current valves
> and
> > weld shut the hole in the end.  That's it. :>)
> >
> > Mike Kopstain
> > Midwest SHO Specialists
> > 827 North Chestnut Avenue
> > Arlington Heights, IL 60004
> > www.MidwestSHO.com
> > Sales@midwestsho.com
> > ----- Original Message -----
> > From: "Bruce Malachuk" <bmalach1@nycap.rr.com>
> > To: "SHOtimes" <shotimes@autox.team.net>
> > Sent: Friday, March 07, 2003 10:15 PM
> > Subject: [Shotimes] Brake Bias Plugs
> >
> >
> > > I've read everything on the shoforum about these, and they sound
pretty
> > > simple. Paul Nimz had listed some specs about them " The thread is
> M16x1.0
> > and
> > > you need two Vitron O-rings 3/8" OD x 1/4" ID x 1/16" and I was
> wondering
> > if
> > > anyonecould direct me to finding a local kind of place to get what I
> need
> > to
> > > make my own? I'd buy some from SHOnut or Midwest SHO, but I wanted to
> see
> > if I
> > > could make them myself. I can't imagine that they cost more than a few
> > bucks
> > > to make. Like could I go to Home Depot and find something to use, or
> maybe
> > a
> > > plumbing supply place? Kinda want to do this for as little as
possible.
> > Maybe
> > > I could make plugs outta some JBweld, though that wouldn't be
> reversible.
> > >
> > > Thanks in advance
> > >
> > > Bruce
> > > _______________________________________________
> > > Shotimes mailing list
> > > Shotimes@autox.team.net
> > > http://www.team.net/mailman/listinfo/shotimes
> _______________________________________________
> Shotimes mailing list
> Shotimes@autox.team.net
> http://www.team.net/mailman/listinfo/shotimes