[Shotimes] rod bearings

[Kerry Kinion]

Another couple stupid questions.  What kind of silicone do I use on the
oil pan sides where there is no gasket?  Where do I place the bead
exactly?  There are some grooves right down the middle stopping before
the bolt holes.  Do I just run it right thru these and around the bolt
holes?

Thanks!

Kerry
-----Original Message-----
From: Ron Porter [mailto:ronporter@prodigy.net] 
Sent: Thursday, May 01, 2003 11:25 AM
To: 'Paul Nimz'; shotimes@autox.team.net
Subject: RE: [Shotimes] rod bearings

Gee we thought you were smart when we didn't see your error. Now that
you
pointed it out.........  ;'-)

Ron Porter 

-----Original Message-----
From: shotimes-admin@autox.team.net
[mailto:shotimes-admin@autox.team.net]
On Behalf Of Paul Nimz
Sent: Thursday, May 01, 2003 1:49 PM
To: Paul Nimz; 'Kerry Kinion'; shotimes@autox.team.net
Subject: Re: [Shotimes] rod bearings


drives = driver


----- Original Message ----- 
From: "Paul Nimz" <pmnimz@v8sho.com>
To: "'Kerry Kinion'" <kerry@kinionfurniture.com>;
<shotimes@autox.team.net>
Sent: Thursday, May 01, 2003 12:24 PM
Subject: Re: [Shotimes] rod bearings


> Which front???  :)
>
> I did two dry runs and the third time with the silicone on it just pop
right
> in.  Angle the pan downward towards the back of the car and insert
upward
> towards the radiator side of the motor making contact first on the
drives
> side.
>
> Paul Nimz
> '97 TR SHO
> '93 EG mtx SHO
>
>
> ----- Original Message ----- 
> From: "Ron Porter" <ronporter@prodigy.net>
> To: "'Kerry Kinion'" <kerry@kinionfurniture.com>;
<shotimes@autox.team.net>
> Sent: Thursday, May 01, 2003 11:57 AM
> Subject: RE: [Shotimes] rod bearings
>
>
> > The "trick" is to angle one side of the pan (I "think" the front) to
about
> > 45 degrees and it comes out.
> >
> > The idler bearing is that round thing bolted to the subframe that
keeps
> the
> > pan from coming out easily! It has one of the axles running through
it.
> >
> > Ron Porter
> >
> > -----Original Message-----
> > From: shotimes-admin@autox.team.net
[mailto:shotimes-admin@autox.team.net]
> > On Behalf Of Kerry Kinion
> > Sent: Thursday, May 01, 2003 2:33 AM
> > To: shotimes@autox.team.net
> > Subject: RE: [Shotimes] rod bearings
> >
> >
> > OK - I know this is REALLY stupid, but what and where is the idler
> > bearing and half-shaft?  I'm learning (slow as it may be) one part
at a
> > time!  This might be a big help in getting the pan back on though,
as I
> > had a heck of a time dropping the thing out!!
> >
> > I'm feeling a little intimidated, but also pretty pumped, looking up
> > into my engine from the bottom.
> >
> > Kerry
> > -----Original Message-----
> > From: BJamesjr@aol.com [mailto:BJamesjr@aol.com]
> > Sent: Wednesday, April 30, 2003 11:43 AM
> > To: Kerry Kinion; shotimes@autox.team.net
> > Subject: Re: [Shotimes] rod bearings
> >
> > > Tomorrow: Finish taking Y-Pipe off, starter out,
> > > oil pan off.
> >
> > As I recall on my 90MTX, one or 2 of the oil pan bolts near the
> > transmission were very difficult to get to.  I had to buy a 1/4"
drive
> > universal joint to get in there.
> >
> > I loosened the idler bearing for one of the half-shafts but did not
> > remove it.  This gave me just enough clearance to squirm the pan
out.
> > It was tight but did come out.
> > _______________________________________________
> > Shotimes mailing list
> > Shotimes@autox.team.net
> > http://www.team.net/mailman/listinfo/shotimes
> > _______________________________________________
> > Shotimes mailing list
> > Shotimes@autox.team.net
> > http://www.team.net/mailman/listinfo/shotimes
> _______________________________________________
> Shotimes mailing list
> Shotimes@autox.team.net
> http://www.team.net/mailman/listinfo/shotimes
_______________________________________________
Shotimes mailing list
Shotimes@autox.team.net
http://www.team.net/mailman/listinfo/shotimes
_______________________________________________
Shotimes mailing list
Shotimes@autox.team.net
http://www.team.net/mailman/listinfo/shotimes