[Shotimes] Leftover nut after clutch job

[Ian Fisher]

...and they are probably too big to be the LCA pinch
bolt nuts, right?

We had an expression when I was repairing computers
and printers years back; "if you put it back together
and there aren't any spare parts or screws left then
you must've done something wrong."

=)

Ian

--- Edward Mazurek <emazurek@cisco.com> wrote:

> Hi Mark,
> 
> The two motor mount nuts (I believe) are only 18mm
> just like the
> 4 subframe bolts. I used the same socket to snug
> both nuts and
> all 4 subframe bolts so I'm pretty sure of this. So,
> they are
> much smaller than this nut.
> 
> But, this nut is smaller than the two rack nuts
> which (I think) I
> used a 24mm socket on.
> 
> Thanks,
> 
> Ed
> 
> Mark Nunnally wrote:
> 
> >21mm nuts (2) are the motor mount nuts, front and
> rear.  the subframe are 18mm bolts and the rack nuts
> are 15/16
> >
> >mark
> >
> >-----Original Message-----
> >  
> >
> >>From: Edward Mazurek <emazurek@cisco.com>
> >>Sent: Mar 2, 2006 11:29 AM
> >>To: Ian Fisher <dataflash@yahoo.com>
> >>Cc: SHOTimes <shotimes@autox.team.net>
> >>Subject: Re: [Shotimes] Leftover nut after clutch
> job
> >>
> >>Hi Ian,
> >>
> >>I could get a picture but I haven't yet. It takes
> a 21mm socket
> >>so it's big. It is a standard looking nut with the
> round flange
> >>at the bottom. I can get a picture and email it to
> you.
> >>
> >>Thanks!
> >>
> >>Ed
> >>
> >>Ian Fisher wrote:
> >>
> >>    
> >>
> >>>Do you have a picture?
> >>>
> >>>Ian
> >>>
> >>>--- Edward Mazurek <emazurek@cisco.com> wrote:
> >>>
> >>> 
> >>>
> >>>      
> >>>
> >>>>Hi,
> >>>>
> >>>>95 MTX...
> >>>>
> >>>>I just got the subframe back in and I seem to
> have
> >>>>an "extra"
> >>>>large nut left over. :(
> >>>>
> >>>>I have the 4 subframe bolts in.
> >>>>I have the two passgenger side mount nuts in
> (front
> >>>>& rear).
> >>>>I have the two huge nuts for the rack in.
> >>>>I have the two driver's side subframe to mount
> bolts
> >>>>in.
> >>>>I also have the two smaller nuts for the
> driver's
> >>>>side
> >>>>shock mount that go to the trans.
> >>>>
> >>>>What am I missing?
> >>>>
> >>>>BTW, the 96 subframe bushings worked great! I
> didn't
> >>>>even have to
> >>>>trim the ridges off as my subframe had the
> >>>>corresponding notches
> >>>>already.
> >>>>
> >>>>Thanks!
> >>>>
> >>>>Ed
> >>>>_______________________________________________
> >>>>Shotimes mailing list
> >>>>Shotimes@autox.team.net
> >>>>http://www.team.net/mailman/listinfo/shotimes
> >>>>        
> >>>>
> >>>Tired of spam?  Yahoo! Mail has the best spam
> protection around 
> >>>http://mail.yahoo.com 
> >>>      
> >>>
> >>_______________________________________________
> >>Shotimes mailing list
> >>Shotimes@autox.team.net
> >>http://www.team.net/mailman/listinfo/shotimes
> _______________________________________________
> Shotimes mailing list
> Shotimes@autox.team.net
> http://www.team.net/mailman/listinfo/shotimes
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com