[Tigers] dipstick tube 260CID engine

[Buck Trippel]

There are two part numbers in the Parts Manual for dipsticks.

 

I found a drawing of the earlier version (1224808) but was unsuccessful on the latter (6100734).

 

The drawing I found referenced Ford part number C20E-6750-A, but I doubt they differed very much.

 

Buck

 

 

From: Tigers <tigers-bounces at autox.team.net> On Behalf Of D or G at sbc via Tigers
Sent: Thursday, February 27, 2020 5:23 PM
To: 'Ron Fraser' <rfraser at bluefrog.com>; rick at atmospherebuilders.com
Cc: tigers at autox.team.net
Subject: Re: [Tigers] dipstick tube 260CID engine

 

Scott Drake has them but you can't purchase them directly from him, you have to go through one of his dealers (they are all over the US).

 

I find it strange that Rootes shows the Ford part number for the dip stick tube which has to be bent to work in a Tiger, but they don't show a Ford number for the long finger pull dip stick which is a regular Ford stick with the end bent to about 85 degrees, way easier to do than the tube.

 

David Franchi

 

On Thursday, February 27, 2020, 4:58:02 PM PST, Ron Fraser via Tigers < > wrote: 

 

 

Darn I forgot to include

Most of the Mustang and Falcon catalogs should carry these parts.

I believe Scott Drake is making them.

 

Ron Fraser

 

From: Tigers <tigers-bounces at autox.team.net <mailto:tigers-bounces at autox.team.net> > On Behalf Of Ron Fraser via Tigers
Sent: Thursday, February 27, 2020 7:51 PM
To: rick at atmospherebuilders.com <mailto:rick at atmospherebuilders.com> 
Cc: tigers at Autox.Team.Net <mailto:tigers at Autox.Team.Net> 
Subject: Re: [Tigers] dipstick tube 260CID engine

 

Here is some additional info

 

Tube – C2OZ-6754-A is listed by Ford at 15.83” long, for 260 and 289 engines with generator

I measured my tube at very near this length with about 14 ¾” above the timing cover to its end.

 

Dipstick - C30Z-6750-B 

This is the Ford part number listed for 1964, 260 and 289 engines with generators.

22.48" shield to FULL

23.32" shield to ADD 

24.44" shield to end

This is extremely close to the measurements I took on my dipstick.

Additionally:     Width = .295”    Thickness = .060”

 

Ron Fraser

 

From: Tigers <tigers-bounces at autox.team.net <mailto:tigers-bounces at autox.team.net> > On Behalf Of Richard Hyatt via Tigers
Sent: Thursday, February 27, 2020 5:27 PM
To: tigers at autox.team.net <mailto:tigers at autox.team.net> 
Subject: [Tigers] dipstick tube 260CID engine

 

When I got my engine back from a high performance machine shop, they happily pointed out the new chrome dipstick and dipstick tube they had obtained and installed in the process. Unfortunately this will not fit correctly as you can imagine. Mysteriously although they had returned some other parts, the dipstick was missing and the old tube battered to the point of no use. I am hoping to find a solution…….not sure if anyone has ever made a pattern of the original tube or has any ideas. Thanks.

Rick

_______________________________________________

tigers at autox.team.net <mailto:tigers at autox.team.net> 

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/pipermail/tigers  <http://www.team.net/pipermail/tigers%20> http://autox.team.net/archive

Unsubscribe: http://autox.team.net/mailman/options/tigers/orr4sale@sbcglobal.net



-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/tigers/attachments/20200227/ae4c8465/attachment-0001.htm>