[Zmagnette] Fwd: Uncaught bounce notification

[Mike]

What I have will work, mine only make contact on the back edge, looks like they would have to be made with more of an angle to seal all the way around.

Mike H.

> On Apr 2, 2014, at 4:34 PM, Steve Hanegan <steve at betterwitnesses.com> wrote:
> 
> MGA & Magnette not the same part
> 
> Steve H
> 
>> On Wednesday, April 2, 2014, <jeffmgcar at aol.com> wrote:
>> I did them for my MGA and got them from either Holden, or Anglo Parts in Europe. You can get their cataloge on-line.
>>  
>> Jeff Becker
>> -----Original Message-----
>> From: Mike <mgmike62 at gmail.com>
>> To: List for the Z Magnette Group - North America <zmagnette at autox.team.net>
>> Sent: Wed, Apr 2, 2014 12:27 pm
>> Subject: Re: [Zmagnette] Fwd: Uncaught bounce notification
>> 
>> If one wanted to buy new Wheel Box rubber bits the circular ones that have the angled end, where might one look?
>> 
>> Mike H.
>> 
>> On Apr 2, 2014, at 12:57 PM, Steve Hanegan <steve at betterwitnesses.com> wrote:
>> 
>>> Mike,
>>> 
>>>  I was able to feed the rack and wheel boxes through with the scuttle vent in place. Feed the rack through from the passenger side with the dash out. I will get a chance to do this again (and fully document it) when I get to re-assembly of this:
>>> 
>>> <BUSER MG 001.jpeg>
>>> 
>>> Steve H.
>>> 
>>>> On Apr 2, 2014, at 9:35 AM, Mike <mgmike62 at gmail.com> wrote:
>>>> 
>>>> Steve H,
>>>> Does the Scuttle Vent need to come out?
>>>> 
>>>> Mike H.
>>>> 
>>>> On Apr 2, 2014, at 11:58 AM, Steve Hanegan <steve at betterwitnesses.com> wrote:
>>>> 
>>>>> The rubber bits around the wheel boxes on the inside of the cowl are only really necessary if you want to keep water on the outside of the car from getting inside the car... While they are off, it wouldn't hurt to soak and rub those wheel box rubbers in/with some warm olive oil to return some of their suppleness...
>>>>> 
>>>>> MG put very few unnecessary or "extra" parts in their cars.
>>>>> 
>>>>> Steve H.
>>>>> 
>>>>>  
>>>>>> On Apr 2, 2014, at 8:45 AM, Mike <mgmike62 at gmail.com> wrote:
>>>>>> 
>>>>>> Thanks Allen,
>>>>>> Usually I get the posts back, when I don't I figure it didn't go through, the Rubber pieces that go around the wheel box shafts are the problem and I wonder if they are really necessary? The Scuttle vent is already installed and I HATE to take it back apart. One step forward two steps back....
>>>>>> Thanks,
>>>>>> Mike
>>>>>> 
>>>>>> On Apr 2, 2014, at 11:15 AM, Allen Bachelder <bachldrs at comcast.net> wrote:
>>>>>> 
>>>>>>> Mike Hickman has tried to send this message to the list but something caused it to bounce. I'm hoping Mark Bradakis will advise me how to solve it, but in the meantime, responses to Mike's question - below - would be appreciated.
>>>>>>> 
>>>>>>> Mike, it just so happens that I installed my wheel boxes and tubes before installing the scuttle vent, and had no problem. I didn't try to do it the other way 'round.  If you're having  a problem, this might be at least part of your answer. If you do remove the scuttle vent and mechanism, draw a lot of pictures and make notes to yourself on how it comes apart because I remember there were just a whole lot of incorrect ways to put it back together such that everything fits but nothing works!
>>>>>>> 
>>>>>>> FWIW,
>>>>>>> Allen
>>>>>>> ****************************************************************
>> 
>> _______________________________________________
>> Zmagnette mailing list
>> 
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe/Manage: http://autox.team.net/mailman/options/zmagnette/jeffmgcar@aol.com
>> 
> _______________________________________________
> Zmagnette mailing list
> 
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage: http://autox.team.net/mailman/options/zmagnette/mgmike62@gmail.com
> 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/zmagnette/attachments/20140402/51f2621a/attachment.html>