mgs
[Top] [All Lists]

Re: [Mgs] MGA sputtering engine and bad replacement parts

To: "RANDELL KEGG" <RANDELL_KEGG@msn.com>, "Robert J. Guinness"
Subject: Re: [Mgs] MGA sputtering engine and bad replacement parts
From: Barrie Robinson <barrie@look.ca>
Date: Thu, 26 Nov 2009 16:34:43 -0500
Folks,

When I worked for Marconi in the UK building defense systems we 
always "soaked" our computers for not less than 100 hours - usually 
250.  If no capacitors soured during this run we reckoned they would 
work forever (but we had triple standbys!!)


At 01:59 PM 11/26/2009, RANDELL KEGG wrote:
>Back in the 1970s, I worked as a mechanic for some of the local Volkswagen
>dealers. When doing
>tune ups, we never replaced the condenser if the car was running decently when
>it came in. As you say, "seasoned" condensers seem to last for many years. New
>condensers have a significant failure rate when
>  new. In those days, we were dealing with factory parts, and still 
> it was well
>known among the mechanics to
>not replace the condenser unless it was necessary. I am still working on cars,
>and this situation is still happening today.
>
>Randy Kegg
>
>
>   ----- Original Message -----
>   From: Simon Matthews<mailto:simon.d.matthews@gmail.com>
>   To: Robert J. Guinness<mailto:guinness@stclegal.com>
>   Cc: MG List<mailto:mgs@autox.team.net>
>   Sent: Thursday, November 26, 2009 10:20 AM
>   Subject: Re: [Mgs] MGA sputtering engine and bad replacement parts
>
>
>   Robert,
>
>   I have suggested on s3veral occasions on this mailing list that
>   condensers should not be replaced unless they have failed. There is
>   plenty of anecdotal evidence to suggest that condensers have a high
>   early failure rate, but  those that survive early failure will last
>   for a long time (many decades).
>
>   Hence, by routinely replacing condensers, you are much more likely to
>   have a condenser fail, because you risk the early failure of your
>   newly replaced condenser.
>
>   Simon
>
>   On Thu, Nov 26, 2009 at 5:09 AM, Robert J. Guinness
>   <guinness@stclegal.com<mailto:guinness@stclegal.com>> wrote:
>   > I want to thank all those who offered advice on diagnosing my MGA's
>   > sputtering and dieing engine.  The culprit was a bad condenser (which I
>   > replaced less than a year ago).  Are our parts sources becoming
>unreliable?
>   >  I had to replace the points I installed at the same time.  Have others
>   > experienced bad mechanical replacement parts lately (as opposed to body,
>   > rubber, interior, etc.), or is it just me?  Or did the bad new condenser
>   > cause problems with the points?
>   > --
>   > Robert Guinness
>   >
>   >
>   >
>   > __________ Information from ESET Smart Security, version of virus
>signature
>   > database 4637 (20091125) __________
>   >
>   > The message was checked by ESET Smart Security.
>   >
>   > http://www.eset.com<http://www.eset.com/>
>   >
>   > _______________________________________________
>   >
>   > Support Team.Net
>http://www.team.net/donate.html<http://www.team.net/donate.html>
>   >
>   > Mgs@autox.team.net<mailto:Mgs@autox.team.net>
>   >
>http://autox.team.net/mailman/listinfo/mgs<http://autox.team.net/mailman/list
>info/mgs>
>   >
>   > http://www.team.net/archive<http://www.team.net/archive>
>
>   _______________________________________________
>
>   Support Team.Net
>http://www.team.net/donate.html<http://www.team.net/donate.html>
>
>   Mgs@autox.team.net<mailto:Mgs@autox.team.net>
>   http://autox.team.net/mailman/listinfo/mgs<http://autox.team.net/mailman/li
>stinfo/mgs>
>
>   http://www.team.net/archive<http://www.team.net/archive>
>
>_______________________________________________
>
>Support Team.Net  http://www.team.net/donate.html
>
>Mgs@autox.team.net
>http://autox.team.net/mailman/listinfo/mgs
>
>http://www.team.net/archive

Regards

Barrie
barrie@look.ca
(705) 721-9060 

_______________________________________________

Support Team.Net  http://www.team.net/donate.html

Mgs@autox.team.net
http://autox.team.net/mailman/listinfo/mgs

http://www.team.net/archive

<Prev in Thread] Current Thread [Next in Thread>