tigers
[Top] [All Lists]

Re: [Tigers] Exhaust Manifold Issues

To: "David or Gary Franchi" <wwwdg@webtv.net>,tigers-bounces@autox.team.net,"'Carlo Bernardino'" <crbdino@me.com>,tigers@autox.team.net
Subject: Re: [Tigers] Exhaust Manifold Issues
From: jay.laifman@gmail.com
Date: Tue, 8 May 2012 17:17:09 +0000
Delivered-to: tigers-archive@autox.team.net
Delivered-to: tigers@autox.team.net
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20120113; h=x-rim-org-msg-ref-id:message-id:content-transfer-encoding:reply-to :x-priority:references:in-reply-to:sensitivity:importance:subject:to :from:date:content-type:mime-version; bh=9h0ag13byy348Bw8XAR3mS8INSUPoJSm0Lu4RRXyEAo=; b=Bvqd24UzCzAn9JnGGFka93uzF+L2a7ePMPXPdtYem3SJ9nxcQR85cWw33PZckbihnZ 6b1FvRj3zBFKGvgnnIZwHiEaXNBG4G0Z9KtRybJOvANvhgzsZsrwA0GwaTr3QGca+pZN Z3Z9lQBIkrA1J3j3pI9Mu/1tavuILFZqbBmRqH0XzeVJwxdzQ8wfHSavRPE1pmbNaetJ 2PTaDIvOaqEUTt4EOgxkB0kD+2zpUkYbjGQOzTpMq/WP7/ko3d6tl2OF3EvPwm2Ji+Wu RYjlCguK15ZbCasndkRo8XWXxWFfYYIxU5GEjce+WIFtscaqGYfBWf/BTwXMpQO2cigE FhCg==
List-archive: <http://autox.team.net/pipermail/tigers>
List-help: <mailto:tigers-request@autox.team.net?subject=help>
List-id: Sunbeam Tigers <tigers.autox.team.net>
List-post: <mailto:tigers@autox.team.net>
List-subscribe: <http://autox.team.net/mailman/listinfo/tigers>, <mailto:tigers-request@autox.team.net?subject=subscribe>
List-unsubscribe: <http://autox.team.net/mailman/options/tigers>, <mailto:tigers-request@autox.team.net?subject=unsubscribe>
References: <BAY148-ds11DB47A165D3C0AF6854F9AD100@phx.gbl>
Sensitivity: Normal
Can you give more details on this aluminum paint?  How do I identify of it is 
the right type?  Where is it sold?  Would it be good for an exhaust application 
that uses a gasket, but tends to leak?  How is the clean up the next time it 
has to be pulled apart?

Sent from my Verizon Wireless BlackBerry

-----Original Message-----
From: David or Gary Franchi <wwwdg@webtv.net>
To: 'Carlo Bernardino'<crbdino@me.com>; <tigers@autox.team.net>
Subject: Re: [Tigers] Exhaust Manifold Issues

I would first try putting the bolts that are missing back in and tighten them 
up, you might get lucky and it won't leak, as Ron stated there was no gasket 
(if you have stock manifolds). If you put gaskets in the bolts will need to be 
re-tightened now and then as the gaskets compress over time, they can also burn 
out and leak. 
It is best not to use gaskets. If you can't fix the leak by replacing the 
missing bolts I would remove the manifold and check to make sure it is flat, 
not warped, clean the manifold and head surface with sandpaper then coat the 
manifold mating surfaces with a couple heavy coats of aluminum paint (it has to 
be aluminum paint, not silver) let dry about 10 min. and install it. I have 
fixed lots of leaking manifolds with this method. 

David Franchi


-----Original Message-----
From: Ron Fraser
Sent: Tuesday, May 8, 2012 4:25 AM
To: 'Carlo Bernardino', tigers@autox.team.net
Subject: Re: [Tigers] Exhaust Manifold Issues

Rob
        If you are running a stock Tiger engine and manifolds there is no
exhaust manifold gasket but I believe they are available.   You pull all the
bolts except the first and last which are just loose, some gaskets slide
onto those 2 bolts then install the rest of the bolts.

There is a lock tap for the bolts - C2OZ-9A447-A - these come in a package
of 8 and are still available.  I have seen other companies with tabs and
clips to keep their bolts from backing out.  Note there are 2 different
length bolt for the stock Tiger exhaust manifold.
3/8"x 1 1/4"
3/8"x 2"

Torque bolts to 18 - 24 ft lbs.

See Tigers United for Ford Parts List under engine
http://www.tigersunited.com/resources/parts_rs260/FactParts.asp

Ron Fraser



-----Original Message-----
From: tigers-bounces@autox.team.net [mailto:tigers-bounces@autox.team.net]
On Behalf Of Carlo Bernardino
Sent: Tuesday, May 08, 2012 1:15 AM
To: tigers@autox.team.net
Subject: [Tigers] Exhaust Manifold Issues


Dear Tiger Gurus,
I was enjoying the Monterey weather this weekend and chasing down porsches
when the engine started sounding rough. I short shifted home and popped the
boot. Low and behold my exhaust manifold had ejected a number of bolts. So
much for bolts being seized on the manifold. Anyway, I suspect I need to
replace the gasket and bolts. So some questions for the gurus:

1) Is it possible to change the gasket with the engine in situ?
2) Any tricks in getting things 'just right'?
3) What are the bolts to be torqued to?

Thanks for all your advice on advance.
Rob



Rob in Carmel, CA
1966 Mk1A Tiger
B382000262 LRXFE
JAL660245
Color Code 39: Carnival Red
TAC# 0519
_______________________________________________

tigers@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe:
http://autox.team.net/mailman/options/tigers/rfraser@bluefrog.com
_______________________________________________

tigers@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: http://autox.team.net/mailman/options/tigers/wwwdg@webtv.net
_______________________________________________

tigers@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: http://autox.team.net/mailman/options/tigers/jay.laifman@gmail.com
_______________________________________________

tigers@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: 
http://autox.team.net/mailman/options/tigers/tigers-archive@autox.team.net



<Prev in Thread] Current Thread [Next in Thread>