triumphs
[Top] [All Lists]

Fwd: Returned mail: Host unknown (Name server: autox.team.net.-: host no

To: triumphs@autox.team.net
Subject: Fwd: Returned mail: Host unknown (Name server: autox.team.net.-: host not found)
From: ArthurK101@aol.com
Date: Mon, 25 Nov 1996 11:58:43 -0500
---------------------
Forwarded message:
From:   MAILER-DAEMON@aol.com (Mail Delivery Subsystem)
To:     ArthurK101@aol.com
Date: 96-11-24 13:32:27 EST

This is a MIME-encapsulated message

--NAA18607.848860317/emout08.mail.aol.com

The original message was received at Sun, 24 Nov 1996 13:31:23 -0500
from root@localhost

    If your mail was returned due to a potentially misspelled AOL
e-mail address, we may be able to assist you in finding the correct
address.  Point your WWW browser at

        http://www.idot.aol.com/search/

   Here you will find instructions and a simple form to help you
locate the email address you are looking for!


    NOTE:  we cannot and will not divulge private information about
members.  Please only use the search resource if you believe that you
may have misspelled a member's e-mail address.

        -AOL Postmaster

   ----- The following addresses had delivery problems -----
triumphs@autox.team.net.-  (unrecoverable error)

   ----- Transcript of session follows -----
550 triumphs@autox.team.net.-... Host unknown (Name server: autox.team.net.-:
host not found)

   ----- Original message follows -----

--NAA18607.848860317/emout08.mail.aol.com

Return-Path: ArthurK101@aol.com
1996 13:31:23 -0500
Date: Sun, 24 Nov 1996 13:31:23 -0500
From: ArthurK101@aol.com
To: andertonm@juno.com
cc: triumphs@autox.team.net.-
Subject: Re: Dash knob removal

In a message dated 96-11-23 17:58:49 EST, andertonm@juno.com (Mark R.
Anderton) writes:

> I guess what I didn't say in my earlier message was
>  that I did refinish the dash on my 72 TR6 about 5 years ago with some
>  success, but I felt like I was extremely lucky in that I was able to
>  chip off the old finish without damaging the very fragile veneer.  Any
>  one attempting this should NOT take sandpaper to the veneer. <

Amen.  I used a mild stripper from Sears and CAREFULLY used a thin putty
knife to scrape the old finish off the veneer.  The veneer was not damaged.
 Next I painted the air vent and speedo/tach edges with a brown Krylon paint
(close to the original color).  I then used a polyurethane clear gloss
finish, wet sanding with 1200 grit between each of 4 coats.  Looks like new

> Apart from the fact that I wasn't happy with the color of the stain/finish
I put
>  back on, it has served well til recently.  The plywood substrate has
>  succmbed to age and is falling apart, so I got a new dash from TRF.
>  

As far as the plywood substrate - I used several coats of mineral oil (tung
oil would also work) applied to the back of the wood dash.  This soaked in
from the back and has prevented the plywood from deteriorating. 

Thanks for the story about the radio and the oil line.  Don't know one of us
who hasn't done or failed to do some simple thing which resulted in a minor
(and sometimes major) catastrophe of that kind. :-)
Art Kelly '64TR4 CT33118L

--NAA18607.848860317/emout08.mail.aol.com--



<Prev in Thread] Current Thread [Next in Thread>