- 1. [oletrucks] Drive Shaft Donors (score: 1)
- Author: Paul Blosser <paulb@todays-tech.com>
- Date: Wed, 24 May 2000 13:34:44 -0500
- I set the engine and transmission (350/350) in the bare frame for the last time this weekend. It's all nestled in there nice and pretty. I have the power steering & alternator on, the power brake mas
- /html/oletrucks/2000-05/msg00709.html (8,541 bytes)
- 2. Re: [oletrucks] Drive Shaft Donors (score: 1)
- Author: MKlepp4335@cs.com
- Date: Wed, 24 May 2000 20:01:13 EDT
- << Do you all have any recommendations on either a donor drive shaft or recommendation on having one built? >> Paul, I went to the junk yard, got a shaft with the correct size u-joints to match trans
- /html/oletrucks/2000-05/msg00713.html (7,530 bytes)
- 3. Re: [oletrucks] Drive Shaft Donors (score: 1)
- Author: "WR Teto" <monadnoc@crystal-mtn.com>
- Date: Thu, 25 May 2000 01:45:39 -0400
- Paul, I roamed around the junkyard, probably measured about 50 shafts until I found one from an 80's Oldsmobile station wagon that fit "as-is". I found that most sedan drive shafts from the 80's will
- /html/oletrucks/2000-05/msg00717.html (8,679 bytes)
- 4. Re: [oletrucks] Drive Shaft Donors (score: 1)
- Author: ADvent@thuntek.net
- Date: Thu, 25 May 2000 07:41:56 -0700
- WR, Do you remember what model wagon that was? -- New Mexico Jim 50 3100 ½ ton 51 6??? two ton dump 54 two ton for parts oletrucks is devoted to Chevy and GM trucks built between 1941 and 195
- /html/oletrucks/2000-05/msg00718.html (9,000 bytes)
- 5. Re: [oletrucks] Drive Shaft Donors (score: 1)
- Author: "WR Teto" <monadnoc@crystal-mtn.com>
- Date: Thu, 25 May 2000 10:21:26 -0400
- Jim, I don't know the year for sure (positive it was 80's though), and I had my notes listed as it coming from an Olds "Custom Cruiser" station wagon. In retrospect, the length you need depends on se
- /html/oletrucks/2000-05/msg00720.html (7,979 bytes)
- 6. Re: [oletrucks] Drive Shaft Donors (score: 1)
- Author: "Claude" <cramey@n-link.com>
- Date: Thu, 25 May 2000 10:50:48 -0500
- and weld and balance it. I had a driveshaft from a 70's Malibu cut down and new crossover U-joints installed, $115. Claude '59 Fleetside oletrucks is devoted to Chevy and GM trucks built between 194
- /html/oletrucks/2000-05/msg00721.html (7,331 bytes)
- 7. RE: [oletrucks] Drive Shaft Donors (score: 1)
- Author: "Peters, Jon C" <jpeters@sikorsky.com>
- Date: Thu, 25 May 2000 15:16:20 -0400
- I had this done for my other project (47' Chevy sedan delivery)... (hey it's sortof a truck!) . It was about $150.00. I'm going over to a 2 piece driveshaft (77' longbed Chevy c20) for my 51 GMC proj
- /html/oletrucks/2000-05/msg00725.html (8,298 bytes)
This search system is powered by
Namazu