Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*TR6\s+rear\s+Bushing\s+replacement\s+procedure\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*TR6\s+rear\s+Bushing\s+replacement\s+procedure\s*$/: 7 ]

Total 7 documents matching your query.

1. TR6 rear Bushing replacement procedure (score: 1): Author: Unknown; Date: Thu, 22 Jan 2004 08:23:24 -0500; I'm soliciting any helpful "Been there done that" advice, tips, tricks, etc. on the job or replacing the trailing arm bushings on a TR-6 (or 4A or 250) Thanks in advance. Scott Tilton 1970 TR6; /html/triumphs/2004-01/msg00620.html (6,991 bytes)
2. Re: TR6 rear Bushing replacement procedure (score: 1): Author: Unknown; Date: Thu, 22 Jan 2004 10:18:47 -0500; I used a 2'' piece of PVC pipe, wide enought to accomidate the bushing, a board, to press against pvc pipe, a socket to press old bushing out,. Then u need a large c-clamp or a large vise to press ou; /html/triumphs/2004-01/msg00628.html (8,191 bytes)
3. Re: TR6 rear Bushing replacement procedure (score: 1): Author: Unknown; Date: Thu, 22 Jan 2004 13:06:05 -0500; Remove the old bushings with any cheapo (HF) three arm gear puller. I bought the set of 3 and used the middle size one. My trailing arms were out of the car when I did mine. Maybe you can do it with; /html/triumphs/2004-01/msg00646.html (7,842 bytes)
4. Re: TR6 rear Bushing replacement procedure (score: 1): Author: Unknown; Date: Thu, 22 Jan 2004 19:20:24 +0100; Threaded rod and correct nuts, plenty of washers of different sizes, washing up liquid for lubrication, pice of pipe or socket to fit over the outside diameter of the eyes in the arms. Simply shove t; /html/triumphs/2004-01/msg00648.html (7,832 bytes)
5. Re: TR6 rear Bushing replacement procedure (score: 1): Author: Unknown; Date: Thu, 22 Jan 2004 13:07:32 -0800; I've had good luck using a small hydraulic "bottle" jack. You can support the bottom on one of the "ears", and use it to push the other bushing out/in. -- Darrell Walker 66 TR4A IRS CTC67956L Vancouv; /html/triumphs/2004-01/msg00652.html (7,372 bytes)
6. Re: TR6 rear Bushing replacement procedure (score: 1): Author: Unknown; Date: Thu, 22 Jan 2004 18:04:43 EST; I did it that way until i heard that was a good way to break off one of the ears - never happened to me but i suppose its possible, especially with some of the earlier ones - quality of casting got b; /html/triumphs/2004-01/msg00657.html (7,488 bytes)
7. RE: TR6 rear Bushing replacement procedure (score: 1): Author: Unknown; Date: Thu, 22 Jan 2004 21:11:55 -0500; I used the following method for removing and installing the rubber bushings on my '70 TR6 trailing arm and have used it on other similar jobs. As was previously mentioned, get some PVC piping that i; /html/triumphs/2004-01/msg00662.html (9,131 bytes)

Current List: 1 - 7
Page: [1]