Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*rear\s+hubs\/half\s+shaft\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*rear\s+hubs\/half\s+shaft\s*$/: 8 ]

Total 8 documents matching your query.

1. rear hubs/half shaft (score: 1): Author: Unknown; Date: Sun, 23 Jan 2000 15:41:57 -0500charset="iso-8859-1"; Hello all from a perrennial lurker. While the Meejut is sleeping under winter anesthesia, i though I'd replace the wire wheel hubs in the rear. Wheels as well of course as they are all shot. So I got; /html/spridgets/2000-01/msg01245.html (7,743 bytes)
2. Re: rear hubs/half shaft (score: 1): Author: Unknown; Date: Sun, 23 Jan 2000 17:09:08 EST; The easiest way to separate the hub from the shaft (and fit the new hub) is to find a workshop that has a bearing press. The welch plug will need replacing. Make sure that each side shaft remains th; /html/spridgets/2000-01/msg01246.html (9,023 bytes)
3. Re: rear hubs/half shaft (score: 1): Author: Unknown; Date: Sun, 23 Jan 2000 18:58:25 -0500; Here are a couple of email conversations that may be of use to you (from the archives at: <http://www.listquest.com/lq/view.cgi?ln=spridgets&mid=2942&sp=&q=boat right+rear+hub+gasket&b=1&s=1&a=1&o=0; /html/spridgets/2000-01/msg01248.html (16,481 bytes)
4. Re: rear hubs/half shaft (score: 1): Author: Unknown; Date: Sun, 23 Jan 2000 20:30:19 -0500; Basket = differential housing! Necessary to open for shaft replacement? How about heat to remove hub? I have heat, but don't have bearing press. Could find one though... I don't know why I have wire; /html/spridgets/2000-01/msg01252.html (10,560 bytes)
5. Re: rear hubs/half shaft (score: 1): Author: Unknown; Date: Sun, 23 Jan 2000 19:18:44 -0800 (PST); What about a gear puller? == Ron Soave IGNORE THE YAHOO MESSAGE BELOW!!!!! Do You Yahoo!?; /html/spridgets/2000-01/msg01255.html (6,781 bytes)
6. Re: rear hubs/half shaft (score: 1): Author: Unknown; Date: Mon, 24 Jan 2000 09:35:11 -0500; Hi Geoff, I also have a '74 Midget with wire wheels... I believe it was an extra cost factory option instead of rostyles. Also, I think you might have an easier time locating good used rear hubs alre; /html/spridgets/2000-01/msg01263.html (7,718 bytes)
7. Re: rear hubs/half shaft (score: 1): Author: Unknown; Date: Mon, 24 Jan 2000 10:32:46 EST; << What about a gear puller? >> I tried a hub puller without success - a DECENT gear puller might get the hub off the shaft but you are still going to need a bearing press to get the new hub back on.; /html/spridgets/2000-01/msg01265.html (7,504 bytes)
8. Re: rear hubs/half shaft (score: 1): Author: Unknown; Date: Mon, 24 Jan 2000 07:56:57 -0800 (PST); No doubt, just a suggestion that has worked in a pinch. For those building their tool collections, pullers are very useful tools to have. == Ron Soave IGNORE THE YAHOO MESSAGE BELOW!!!!! Do You Yaho; /html/spridgets/2000-01/msg01267.html (7,068 bytes)

Current List: 1 - 8
Page: [1]