Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TR\]\s+FW\:\s+Wiper\/Panel\s+Switch\s+Placement\s+TR3\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TR\]\s+FW\:\s+Wiper\/Panel\s+Switch\s+Placement\s+TR3\s*$/: 8 ]

Total 8 documents matching your query.

1. [TR] FW: Wiper/Panel Switch Placement TR3 (score: 1): Author: "Carl TR" <cfmtr3a@verizon.net>; Date: Tue, 28 Jun 2011 13:23:23 -0400; IMO Yes, you should fabricate a ground harness. The factory did rely on the mounting screws and they are far from secure, especially since the screw only goes into a clip nut (rather than into the me; /html/triumphs/2011-06/msg00543.html (7,388 bytes)
2. Re: [TR] FW: Wiper/Panel Switch Placement TR3 (score: 1): Author: "Carl TR" <cfmtr3a@verizon.net>; Date: Wed, 29 Jun 2011 13:44:56 -0400; Finally finished replacing the differential, and AnnaBelle and were bleeding the rear brakes ... no problem. When I went to the front I was dismayed to find the bleeder screw was snapped off level wi; /html/triumphs/2011-06/msg00561.html (8,659 bytes)
3. Re: [TR] FW: Wiper/Panel Switch Placement TR3 (score: 1): Author: "Randall" <tr3driver@ca.rr.com>; Date: Wed, 29 Jun 2011 11:25:37 -0700; -- Original Message -- That's the most psychotic thing I have heard today. Sign me up. But I get to vet my codriver, not take some randomly-assigned person. Phil Ethier West Side Saint Paul Minnesota; /html/triumphs/2011-06/msg00562.html (7,778 bytes)
4. Re: [TR] FW: Wiper/Panel Switch Placement TR3 (score: 1): Author: "Carl TR" <cfmtr3a@verizon.net>; Date: Wed, 29 Jun 2011 15:09:11 -0400; I never snapped mine off but in fear of doing so I started bleeding my calipers by loosening the cross-over pipe. But that was before I sent them off to Peter for rebuilding and he got them out someh; /html/triumphs/2011-06/msg00565.html (8,105 bytes)
5. [TR] FW: Wiper/Panel Switch Placement TR3 (score: 1): Author: cfmtr3a at verizon.net (Carl TR); Date: Tue, 28 Jun 2011 13:23:23 -0400; Resent - Darn RTF.... 1961 TR3A What is the correct placement of the wiper & panel switches? TRA guidelines have Wiper/Panel (Top/middle); changed at TR3 to Panel/Wiper ISTR recall that it was later; /html/triumphs/2011-06/msg01078.html (8,283 bytes)
6. [TR] FW: Wiper/Panel Switch Placement TR3 (score: 1): Author: cfmtr3a at verizon.net (Carl TR); Date: Wed, 29 Jun 2011 13:44:56 -0400; I went digging into the archives and actually found the answer: "As several have pointed out, the earlier cars have the panel light in the top position ... but the rheostat will not fit there. In fac; /html/triumphs/2011-06/msg01097.html (9,349 bytes)
7. [TR] FW: Wiper/Panel Switch Placement TR3 (score: 1): Author: tr3driver at ca.rr.com (Randall); Date: Wed, 29 Jun 2011 11:25:37 -0700; Carl, sorry I didn't get back to you sooner. I meant to check some things when I got home last night, but the TR didn't want to cooperate and I didn't get home until after midnight. Anyway, I see yo; /html/triumphs/2011-06/msg01098.html (8,496 bytes)
8. [TR] FW: Wiper/Panel Switch Placement TR3 (score: 1): Author: cfmtr3a at verizon.net (Carl TR); Date: Wed, 29 Jun 2011 15:09:11 -0400; RE: starter bezel. I was basing my comments on a very grainy image in the TR3 Practical Hints... Looking closer at SPC Plate AD; it appears that you are correct. That does make my life easier as I no; /html/triumphs/2011-06/msg01101.html (8,939 bytes)

Current List: 1 - 8
Page: [1]