I am using 87mm, but since I am racing SCCA that is the max that is legal for
EP. I have a set of custom made Ross 89mm pistons that I used one year with
SCCA Vintage. They are nice pistons, but one has a valve stemed size hole
thru the dome. Too expensive to have 1 made to fix the set, so they will just
sit on the shelf till I get tired of looking at them. Joe(B)
-- "Bill Babcock" <BillB@bnj.com> wrote:
this raises a question. What bore are people using for TR3/4. I've heard from
a few sources that a lot more 89mm pistons get sold than 87, and if folks are
using them, is it because their sanctioning bodies permit it?
Right now I THINK I have 87.5 in Peyote, but I have to admit I'm not sure,
because I have multiple sets of every bore size from 83 to 89, and the last
time Peyote got pistons and sleeves it was one of those frantic at the track
deals (at PIR). To be on the safe side I told SOVREN last year I was using 89
so they moved my classification to DM, which of course it should be in even
if
it has 87mm.
And yes, unless my feeble brain has completely forgotten some mechanical
incident, Peyote went the whole year without a teardown. I don't plan to do
one this winter either. I may try to equal Joe Alexander's record for leaving
my motor alone. If I hadn't knocked the nose off at Mission I would have had
a
whole year without any significant work at all other than the harmonic
balancer falling off. Not only that, I only bought one set of tires (Hoosier
Speedsters) and they're still working pretty darn well. I ran some Hoosier
DOT
radials a few times, but they were left over from the previous year.
-----Original Message-----
From: fot-bounces@autox.team.net on behalf of WEmery7451@aol.com
Sent: Thu 12/21/2006 8:15 PM
To: wensley@adelphia.net; alfetta95@optonline.net
Cc: FOT@autox.team.net
Subject: Re: [Fot] SCCA Archives
In a message dated 12/21/06 12:33:31 PM Pacific Standard Time,
wensley@adelphia.net writes:
<< That was a "Redmond" built Triumph engine and gearbox in that
> Morgan!! I was a little terd then but remember the whole hype
> around my house of Bob going to Riverside. Made the local newspaper. >>
Bob Stanford was the super mechanic with US AIR (Allegheny Airlines at that
time). I had my car up at Chuck Redmond's garage to rebuild my engine and
learn from them how to do it. I haven't progressed much, since I am still
using
most of their techniques.
I remember when Bob would stay up all night pulling out his engine,
rebuilding it, and installing it by day break. Then he would leave from
there
and go
directly to work. The year he went to Riverside, he build another engine
with
87 mm pistons, to get rid of his 87 mm + 0.30 inch pistons. He said that a
certain number of cars get torn down at this event. This move probably cost
him
a little power.
"Sports Car" had a picture on the cover of the beginning of the EP race
coming down a hill. Bob's Morgan was on the inside of the track about half
way
back in the pack.
_______________________________________________
Fot mailing list
Fot@autox.team.net
http://autox.team.net/mailman/listinfo/fot
_______________________________________________
Fot mailing list
Fot@autox.team.net
http://autox.team.net/mailman/listinfo/fot
_____________________________________________________________________
FREE for 30 Days! - Holiday eCards from AmericanGreetings.com
http://track.netzero.net/s/lc?s=197335&u=http://www.americangreetings.com/ind
ex.pd?c=uol5637
_______________________________________________
Fot mailing list
Fot@autox.team.net
http://autox.team.net/mailman/listinfo/fot
|