--===============0903095030702179191==
--00000000000027fe21058c62de7a
Steve--
In light of your email of yesterday telling me you felt that a paper gasket
measuring .015" was too thick to provide sufficient grip between the
abutment shoulder and hub flange to prfevent a spun bearing, this morning I
removed the left axle shaft to check the amount of protrusion of the outer
race beyond the face of the Moss gasket that I recently installed. I was
able to pass a .004" feeler leaf--but no more--between the face of the hub
bearing's outer race and the face of the hub plus paper gasket, which is
within the specification.
Maybe this is due to the paper gasket's having already been under
compression since I installed it last week, and do you think that perhaps
this critical measurement needs to be made after one assembly/disassembly
of the axle shaft to the hub, as obviously the gasket is going to compress
a bit under torquing?
BTW I measured a new, spare paper gasket that came along with the one
installed and it is .014" thick. In any case thanks for focusing on this
issue and I feel better knowing that apparently all is okay.
Best--Michael Oritt
On Thu, Jun 27, 2019 at 5:22 PM Michael Oritt <michael.oritt@gmail.com>
wrote:
> Steve--
>
> I'm going to check my setup tomorrow morning. I'm also going to see if I
> can find my expensive micrometer versus the cheap HF one.... Thanks in any
> case for the tip.
>
> Bear--Michael
>
> On Thu, Jun 27, 2019 at 3:21 PM Steve Gerow <sgerow2@gmail.com> wrote:
>
>> OK, that's too thick and will allow the bearing to spin. Per my
>> experiments it needs to be .003" - .004" in order to work. I made mine out
>> of copier paper, using the Moss as a pattern.
>>
>> On Thu, Jun 27, 2019 at 8:48 AM Michael Oritt <michael.oritt@gmail.com>
>> wrote:
>>
>>> Steve--
>>>
>>> The new paper gasket from Moss mike's to about .015"
>>>
>>> On Tue, Jun 25, 2019 at 11:07 PM Steve Gerow <sgerow2@gmail.com> wrote:
>>>
>>>> Maybe they've thinned it down. I reported my findings to Michael Grant,
>>>> QA Mgr at Moss at the time (since retired).
>>>>
>>>> On Tue, Jun 25, 2019 at 6:04 PM Michael Oritt <michael.oritt@gmail.com>
>>>> wrote:
>>>>
>>>>> Steve--
>>>>>
>>>>> I began seeing a slightly oily "footprint" under my left rear tire a
>>>>> few weeks ago and figured I would have to replace the lip seal. However
>>>>> when I removed the axle I found that there was no paper gasket between the
>>>>> axle flange and the hub, nor any trace of one, nor was there an O ring!
>>>>>
>>>>> My memory is not the best but i know that in the 15 or so years and
>>>>> 60K miles since the car was professionally restored I have never pulled an
>>>>> axle on nor had any leaks from either rear hub. If there was a paper
>>>>> gasket or O ring or sealant it was all gone and the only thing providing
>>>>> any seal at all was the metal-to-metal contact
>>>>>
>>>>> After cleaning everything up and putting in an O ring and paper gasket
>>>>> coated with hylomar I thought that I had better check the oil level as I
>>>>> expected it to be down from the leak. Amazingly the oil level was almost
>>>>> up to the very top with no need to add any at all. So I closed everything
>>>>> up and as I said in my previous post I have probably driven 30-50 miles
>>>>> since with no leak.
>>>>>
>>>>> BTW the paper gasket that Moss supplies is very thin though I did not
>>>>> mike it. I have a spare and will do so tomorrow and will let you know.
>>>>>
>>>>> Best--Michael
>>>>>
>>>>>
>>>>>
>>>>> IO
>>>>>
>>>>> On Tue, Jun 25, 2019 at 5:07 PM Steve Gerow <sgerow2@gmail.com> wrote:
>>>>>
>>>>>> ...or before any trips. How thick was the old gasket you removed?
>>>>>>
>>>>>> On Tue, Jun 25, 2019 at 2:04 PM Steve Gerow <sgerow2@gmail.com>
>>>>>> wrote:
>>>>>>
>>>>>>> What started me thinking was I had leaking seal and a spun bearing.
>>>>>>> Spoke with Tom Monaco (tom's toys) and he said he'd replaced 80+ of
>>>>>>> those
>>>>>>> bearings which didn't sound right to me. He said the heat from the spun
>>>>>>> bearing ate the seal. So I performed the experiment shown in my gallery
>>>>>>> pix
>>>>>>> and reviewed the section in the manual - both of which made it obvious
>>>>>>> what
>>>>>>> was happening.
>>>>>>>
>>>>>>> Your fix may last for a while or forever - dunno. Did you have to
>>>>>>> freeze the bearing and heat the hub to install the bearing? If so it'll
>>>>>>> probably stay for a while.
>>>>>>>
>>>>>>> Might just want to budget time to check it out after the summer
>>>>>>> driving season.
>>>>>>>
>>>>>>> On Tue, Jun 25, 2019 at 1:56 PM Michael Oritt <
>>>>>>> michael.oritt@gmail.com> wrote:
>>>>>>>
>>>>>>>> BTW just last week i put in a Moss paper gasket and hylomar to stop
>>>>>>>> a slight leak at the flange. Not recognizing the issue I did not think
>>>>>>>> to
>>>>>>>> check clearance. I have driven the car perhaps 25-30 miles since with
>>>>>>>> no
>>>>>>>> problem or further leakage so I guess I am asking whether you think the
>>>>>>>> issue would by now have presented itself if the gasket were clamping
>>>>>>>> the
>>>>>>>> bearing race? Or do I need to tear everything apart again?
>>>>>>>>
>>>>>>>> Best--Michael
>>>>>>>>
>>>>>>>> On Tue, Jun 25, 2019 at 4:51 PM Michael Oritt <
>>>>>>>> michael.oritt@gmail.com> wrote:
>>>>>>>>
>>>>>>>>> Steve--
>>>>>>>>>
>>>>>>>>> Later 100's such as mine have the same rear axle, etc. so this
>>>>>>>>> would not be unique to 6 cylinder cars. In any case I think I get the
>>>>>>>>> picture....
>>>>>>>>>
>>>>>>>>> Thanks--Michael
>>>>>>>>>
>>>>>>>>> On Tue, Jun 25, 2019 at 4:43 PM Steve Gerow <sgerow2@gmail.com>
>>>>>>>>> wrote:
>>>>>>>>>
>>>>>>>>>> Also maybe this problem isn't occurring on the 100s.
>>>>>>>>>>
>>>>>>>>>> On Tue, Jun 25, 2019, 1:28 PM Michael Oritt <
>>>>>>>>>> michael.oritt@gmail.com> wrote:
>>>>>>>>>>
>>>>>>>>>>> Steve--
>>>>>>>>>>>
>>>>>>>>>>> Offlist.... Please explain why a too-thick paper gasket would
>>>>>>>>>>> cause the bearing to spin? Wouldn't it simply create more space
>>>>>>>>>>> between
>>>>>>>>>>> the inner face of the axle shaft flange and the outer face of the
>>>>>>>>>>> hub,
>>>>>>>>>>> which in any case should ride correctly on the end of the axle
>>>>>>>>>>> housing/bearing surface regardless? Or does it somehow clamp the
>>>>>>>>>>> inner
>>>>>>>>>>> race of the hub bearing, but if so how and why?
>>>>>>>>>>>
>>>>>>>>>>> Best--Michael
>>>>>>>>>>>
>>>>>>>>>>> On Tue, Jun 25, 2019 at 4:13 PM Steve Gerow <sgerow2@gmail.com>
>>>>>>>>>>> wrote:
>>>>>>>>>>>
>>>>>>>>>>>> Neil,
>>>>>>>>>>>> Leaking axle seals are often caused by spun bearings. Use of
>>>>>>>>>>>> too-thick Moss cardboard gaskets causes bearing to be
>>>>>>>>>>>> insufficiently
>>>>>>>>>>>> gripped (as specified in the manual). Heat from spun bearing
>>>>>>>>>>>> causes seal to
>>>>>>>>>>>> leak. Therefore replacing the seal is not sufficient unless you
>>>>>>>>>>>> correct the
>>>>>>>>>>>> gasket / spun bearing situation.
>>>>>>>>>>>>
>>>>>>>>>>>> For documentation, see:
>>>>>>>>>>>> https://pbase.com/stevegerow/healey_rear_bearing
>>>>>>>>>>>>
>>>>>>>>>>>> >>>
>>>>>>>>>>>> From: Neil McDonald <nmcd10@gmail.com>
>>>>>>>>>>>> To: Healey List <Healeys@autox.team.net>
>>>>>>>>>>>> Cc:
>>>>>>>>>>>> Bcc:
>>>>>>>>>>>> Date: Tue, 25 Jun 2019 10:45:57 -0700
>>>>>>>>>>>> Subject: [Healeys] Leaking Rear Hub Flange
>>>>>>>>>>>> A lot of list chatter about how to stop oil leaks at the rear
>>>>>>>>>>>> hub flange by replacing the paper gasket or using goo of some
>>>>>>>>>>>> sort. Am I
>>>>>>>>>>>> right in thinking that fitting a new oil seal inboard of the wheel
>>>>>>>>>>>> bearing
>>>>>>>>>>>> makes this issue redundant, or is this not necessarily the case?
>>>>>>>>>>>>
>>>>>>>>>>>> Neil
>>>>>>>>>>>> BN6
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> --
>>>>>>>>>>>>
>>>>>>>>>>>> *Steve Gerow*
>>>>>>>>>>>> _______________________________________________
>>>>>>>>>>>> Support Team.Net http://www.team.net/donate.html
>>>>>>>>>>>> Suggested annual donation $12.75
>>>>>>>>>>>>
>>>>>>>>>>>> Archive: http://www.team.net/pipermail/healeys
>>>>>>>>>>>> http://autox.team.net/archive
>>>>>>>>>>>>
>>>>>>>>>>>> Healeys@autox.team.net
>>>>>>>>>>>> http://autox.team.net/mailman/listinfo/healeys
>>>>>>>>>>>>
>>>>>>>>>>>> Unsubscribe/Manage:
>>>>>>>>>>>> http://autox.team.net/mailman/options/healeys/michael.oritt@gmail.com
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>
>>>>>>> --
>>>>>>> *Steve*
>>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>> *Steve*
>>>>>>
>>>>>
>>>>
>>>> --
>>>> *Steve*
>>>>
>>>
>>
>> --
>> *Steve*
>>
>
--00000000000027fe21058c62de7a
Content-Transfer-Encoding: quoted-printable
<div dir=3D"ltr"><div class=3D"gmail_default" style=3D"color:#3333ff">Steve=
--</div><div class=3D"gmail_default" style=3D"color:#3333ff"><br></div><div=
class=3D"gmail_default" style=3D"color:#3333ff">In light of your email of =
yesterday telling me you felt that a paper gasket measuring .015" was =
too thick to provide sufficient grip between the abutment shoulder and hub =
flange to prfevent a spun bearing, this morning I removed the left axle sha=
ft to check the amount of protrusion of the outer race beyond the face of t=
he Moss gasket that I recently installed.=C2=A0 I was able to pass a .004&q=
uot; feeler leaf--but no more--between the face of the hub bearing's ou=
ter race and the face of the hub plus paper gasket, which is within the spe=
cification.=C2=A0</div><div class=3D"gmail_default" style=3D"color:#3333ff"=
><br></div><div class=3D"gmail_default" style=3D"color:#3333ff">Maybe this =
is due to the paper gasket's having already been under compression sinc=
e I installed it last week, and do you think that perhaps this critical mea=
surement needs to be made after one assembly/disassembly of the axle shaft =
to the hub, as obviously the gasket is going to compress a bit under torqui=
ng?=C2=A0=C2=A0</div><div class=3D"gmail_default" style=3D"color:#3333ff"><=
br></div><div class=3D"gmail_default" style=3D"color:#3333ff">BTW I measure=
d a new, spare paper gasket that came along with the one installed and it i=
s .014" thick.=C2=A0 In any case thanks for focusing on this issue and=
I feel better knowing that apparently all is okay.</div><div class=3D"gmai=
l_default" style=3D"color:#3333ff"><br></div><div class=3D"gmail_default" s=
tyle=3D"color:#3333ff">Best--Michael Oritt</div></div><br><div class=3D"gma=
il_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Thu, Jun 27, 2019 at 5:2=
2 PM Michael Oritt <<a href=3D"mailto:michael.oritt@gmail.com";>michael.o=
ritt@gmail.com</a>> wrote:<br></div><blockquote class=3D"gmail_quote" st=
yle=3D"margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padd=
ing-left:1ex"><div dir=3D"ltr"><div class=3D"gmail_default" style=3D"color:=
rgb(51,51,255)">Steve--</div><div class=3D"gmail_default" style=3D"color:rg=
b(51,51,255)"><br></div><div class=3D"gmail_default" style=3D"color:rgb(51,=
51,255)">I'm going to check my setup tomorrow morning.=C2=A0 I'm al=
so going to see if I can find my expensive micrometer versus the cheap HF o=
ne....=C2=A0 Thanks in any case for the tip.</div><div class=3D"gmail_defau=
lt" style=3D"color:rgb(51,51,255)"><br></div><div class=3D"gmail_default" s=
tyle=3D"color:rgb(51,51,255)">Bear--Michael</div></div><br><div class=3D"gm=
ail_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Thu, Jun 27, 2019 at 3:=
21 PM Steve Gerow <<a href=3D"mailto:sgerow2@gmail.com"; target=3D"_blank=
">sgerow2@gmail.com</a>> wrote:<br></div><blockquote class=3D"gmail_quot=
e" style=3D"margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204)=
;padding-left:1ex"><div dir=3D"ltr">OK, that's too thick and will allow=
the bearing to spin. Per my experiments it needs to be .003" - .004&q=
uot; in order to work. I made mine out of copier paper, using the Moss as a=
pattern.<br></div><br><div class=3D"gmail_quote"><div dir=3D"ltr" class=3D=
"gmail_attr">On Thu, Jun 27, 2019 at 8:48 AM Michael Oritt <<a href=3D"m=
ailto:michael.oritt@gmail.com" target=3D"_blank">michael.oritt@gmail.com</a=
>> wrote:<br></div><blockquote class=3D"gmail_quote" style=3D"margin:0px=
0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><di=
v dir=3D"ltr"><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)">S=
teve--</div><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)"><br=
></div><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)">The new =
paper gasket from Moss mike's to about .015"</div></div><br><div c=
lass=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Tue, Jun 25, =
2019 at 11:07 PM Steve Gerow <<a href=3D"mailto:sgerow2@gmail.com"; targe=
t=3D"_blank">sgerow2@gmail.com</a>> wrote:<br></div><blockquote class=3D=
"gmail_quote" style=3D"margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(2=
04,204,204);padding-left:1ex"><div dir=3D"ltr">Maybe they've thinned it=
down. I reported my findings to Michael Grant, QA Mgr at Moss at the time =
(since retired).<br></div><br><div class=3D"gmail_quote"><div dir=3D"ltr" c=
lass=3D"gmail_attr">On Tue, Jun 25, 2019 at 6:04 PM Michael Oritt <<a hr=
ef=3D"mailto:michael.oritt@gmail.com"; target=3D"_blank">michael.oritt@gmail=
.com</a>> wrote:<br></div><blockquote class=3D"gmail_quote" style=3D"mar=
gin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1=
ex"><div dir=3D"ltr"><div class=3D"gmail_default" style=3D"color:rgb(51,51,=
255)">Steve--</div><div class=3D"gmail_default" style=3D"color:rgb(51,51,25=
5)"><br></div><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)">I=
began seeing a slightly oily "footprint" under my left rear tire=
a few weeks ago and figured I would have to replace the lip seal.=C2=A0 Ho=
wever when I removed the axle I found that there was no paper gasket betwee=
n the axle flange and the hub, nor any trace of one, nor was there an O rin=
g!</div><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)"><br></d=
iv><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)">My memory is=
not the best but i know that in the 15 or so years and 60K miles since the=
car was professionally restored I have never pulled an axle on nor had any=
leaks from either rear hub.=C2=A0 If there was a paper gasket or O ring or=
sealant it was all gone and the only thing providing any seal at all was t=
he metal-to-metal contact</div><div class=3D"gmail_default" style=3D"color:=
rgb(51,51,255)"><br></div><div class=3D"gmail_default" style=3D"color:rgb(5=
1,51,255)">After cleaning everything up and putting in an O ring and paper =
gasket coated with hylomar I thought that I had better check the oil level =
as I expected it to be down from the leak.=C2=A0 Amazingly the oil level wa=
s almost up to the very top with no need to add any at all.=C2=A0 So I clos=
ed everything up and as I said in my previous post I have probably driven 3=
0-50 miles since with no leak.=C2=A0=C2=A0</div><div class=3D"gmail_default=
" style=3D"color:rgb(51,51,255)"><br></div><div class=3D"gmail_default" sty=
le=3D"color:rgb(51,51,255)">BTW the paper gasket that Moss supplies is very=
thin though I did not mike it.=C2=A0 I have a spare and will do so tomorro=
w and will let you know.</div><div class=3D"gmail_default" style=3D"color:r=
gb(51,51,255)"><br></div><div class=3D"gmail_default" style=3D"color:rgb(51=
,51,255)">Best--Michael</div><div class=3D"gmail_default" style=3D"color:rg=
b(51,51,255)"><br></div><div class=3D"gmail_default" style=3D"color:rgb(51,=
51,255)"><br></div><div class=3D"gmail_default" style=3D"color:rgb(51,51,25=
5)"><br></div><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)">I=
O</div></div><br><div class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmail=
_attr">On Tue, Jun 25, 2019 at 5:07 PM Steve Gerow <<a href=3D"mailto:sg=
erow2@gmail.com" target=3D"_blank">sgerow2@gmail.com</a>> wrote:<br></di=
v><blockquote class=3D"gmail_quote" style=3D"margin:0px 0px 0px 0.8ex;borde=
r-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir=3D"ltr">...or =
before any trips. How thick was the old gasket you removed?<br></div><br><d=
iv class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Tue, Jun =
25, 2019 at 2:04 PM Steve Gerow <<a href=3D"mailto:sgerow2@gmail.com"; ta=
rget=3D"_blank">sgerow2@gmail.com</a>> wrote:<br></div><blockquote class=
=3D"gmail_quote" style=3D"margin:0px 0px 0px 0.8ex;border-left:1px solid rg=
b(204,204,204);padding-left:1ex"><div dir=3D"ltr"><div>What started me thin=
king was I had leaking seal and a spun bearing. Spoke with Tom Monaco (tom&=
#39;s toys) and he said he'd replaced 80+ of those bearings which didn&=
#39;t sound right to me. He said the heat from the spun bearing ate the sea=
l. So I performed the experiment shown in my gallery pix and reviewed the s=
ection in the manual - both of which made it obvious what was happening.</d=
iv><div><br></div><div>Your fix may last for a while or forever - dunno. Di=
d you have to freeze the bearing and heat the hub to install the bearing? I=
f so it'll probably stay for a while.<br></div><div><br></div><div>Migh=
t just want to budget time to check it out after the summer driving season.=
<br></div></div><br><div class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gm=
ail_attr">On Tue, Jun 25, 2019 at 1:56 PM Michael Oritt <<a href=3D"mail=
to:michael.oritt@gmail.com" target=3D"_blank">michael.oritt@gmail.com</a>&g=
t; wrote:<br></div><blockquote class=3D"gmail_quote" style=3D"margin:0px 0p=
x 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div d=
ir=3D"ltr"><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)">BTW =
just last week i put in a Moss paper gasket and hylomar to stop a slight le=
ak at the flange. Not recognizing the issue I did not think to check cleara=
nce.=C2=A0 I have driven the car perhaps 25-30 miles since with no problem =
or further leakage so I guess I am asking whether you think the issue would=
by now have presented itself if the gasket were clamping the bearing race?=
=C2=A0 Or do I need to tear everything apart again?</div><div class=3D"gmai=
l_default" style=3D"color:rgb(51,51,255)"><br></div><div class=3D"gmail_def=
ault" style=3D"color:rgb(51,51,255)">Best--Michael</div></div><br><div clas=
s=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Tue, Jun 25, 201=
9 at 4:51 PM Michael Oritt <<a href=3D"mailto:michael.oritt@gmail.com"; t=
arget=3D"_blank">michael.oritt@gmail.com</a>> wrote:<br></div><blockquot=
e class=3D"gmail_quote" style=3D"margin:0px 0px 0px 0.8ex;border-left:1px s=
olid rgb(204,204,204);padding-left:1ex"><div dir=3D"ltr"><div class=3D"gmai=
l_default" style=3D"color:rgb(51,51,255)">Steve--</div><div class=3D"gmail_=
default" style=3D"color:rgb(51,51,255)"><br></div><div class=3D"gmail_defau=
lt" style=3D"color:rgb(51,51,255)">Later 100's such as mine have the sa=
me rear axle, etc. so this would not be unique to 6 cylinder cars.=C2=A0 In=
any case I think I get the picture....</div><div class=3D"gmail_default" s=
tyle=3D"color:rgb(51,51,255)"><br></div><div class=3D"gmail_default" style=
=3D"color:rgb(51,51,255)">Thanks--Michael</div></div><br><div class=3D"gmai=
l_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Tue, Jun 25, 2019 at 4:43=
PM Steve Gerow <<a href=3D"mailto:sgerow2@gmail.com"; target=3D"_blank">=
sgerow2@gmail.com</a>> wrote:<br></div><blockquote class=3D"gmail_quote"=
style=3D"margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);p=
adding-left:1ex"><div dir=3D"auto">Also maybe this problem isn't occurr=
ing on the 100s.</div><br><div class=3D"gmail_quote"><div dir=3D"ltr" class=
=3D"gmail_attr">On Tue, Jun 25, 2019, 1:28 PM Michael Oritt <<a href=3D"=
mailto:michael.oritt@gmail.com"; target=3D"_blank">michael.oritt@gmail.com</=
a>> wrote:<br></div><blockquote class=3D"gmail_quote" style=3D"margin:0p=
x 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><d=
iv dir=3D"ltr"><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)">=
Steve--</div><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)"><b=
r></div><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)">Offlist=
....=C2=A0 Please explain why a too-thick paper gasket would cause the bear=
ing to spin?=C2=A0 Wouldn't it simply create more space between the inn=
er face of the axle shaft flange and the outer face of the hub, which in an=
y case should ride correctly on the end of the axle housing/bearing surface=
regardless?=C2=A0 Or does it somehow clamp the inner race of the hub beari=
ng, but if so how and why?</div><div class=3D"gmail_default" style=3D"color=
:rgb(51,51,255)"><br></div><div class=3D"gmail_default" style=3D"color:rgb(=
51,51,255)">Best--Michael</div></div><br><div class=3D"gmail_quote"><div di=
r=3D"ltr" class=3D"gmail_attr">On Tue, Jun 25, 2019 at 4:13 PM Steve Gerow =
<<a href=3D"mailto:sgerow2@gmail.com"; rel=3D"noreferrer" target=3D"_blan=
k">sgerow2@gmail.com</a>> wrote:<br></div><blockquote class=3D"gmail_quo=
te" style=3D"margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204=
);padding-left:1ex"><div dir=3D"ltr"><div>Neil,</div><div>Leaking axle seal=
s are often caused by spun bearings. Use of too-thick Moss cardboard gasket=
s causes bearing to be insufficiently gripped (as specified in the manual).=
Heat from spun bearing causes seal to leak. Therefore replacing the seal i=
s not sufficient unless you correct the gasket / spun bearing situation.</d=
iv><div><br></div><div>For documentation, see:</div><div><a href=3D"https:/=
/pbase.com/stevegerow/healey_rear_bearing" rel=3D"noreferrer" target=3D"_bl=
ank">https://pbase.com/stevegerow/healey_rear_bearing</a></div><div><br></d=
iv><div>
</div><div>>>><br></div><div>From:=C2=A0Neil McDonald <<a href=
=3D"mailto:nmcd10@gmail.com"; rel=3D"noreferrer" target=3D"_blank">nmcd10@gm=
ail.com</a>></div>To:=C2=A0Healey List <<a href=3D"mailto:Healeys@aut=
ox.team.net" rel=3D"noreferrer" target=3D"_blank">Healeys@autox.team.net</a=
>><br>Cc:=C2=A0<br>Bcc:=C2=A0<br>Date:=C2=A0Tue, 25 Jun 2019 10:45:57 -0=
700<br>Subject:=C2=A0[Healeys] Leaking Rear Hub Flange<br><div dir=3D"auto"=
>A
lot of list chatter about how to stop oil leaks at the rear hub flange=20
by replacing the paper gasket or using goo of some sort. Am I right in=20
thinking that fitting a new oil seal inboard of the wheel bearing makes=20
this issue redundant, or is this not necessarily the case?</div><div dir=3D=
"auto"><br></div><div dir=3D"auto">Neil</div><div dir=3D"auto">BN6</div>
<div><br></div><div><br></div><div><br></div><br>-- <br><div dir=3D"ltr" cl=
ass=3D"gmail-m_7286784059870122349gmail-m_595252486213477348gmail-m_-436051=
5329988107071gmail-m_1183269691796420998gmail-m_307167411160119781gmail-m_-=
7051460252659879810gmail-m_-1608126795714715436gmail-m_1588582647885839908g=
mail-m_238194022133982273gmail-m_-2780980072542697186gmail-m_51148827016840=
42763m_1000656405428198813gmail-m_6186304819501026465gmail_signature"><div =
dir=3D"ltr"><div><div dir=3D"ltr"><div><div dir=3D"ltr"><div><div dir=3D"lt=
r"><div><div dir=3D"ltr"><div><font size=3D"2"><b>Steve Gerow<br></b></font=
></div></div></div></div></div></div></div></div></div></div></div></div>
_______________________________________________<br>
rer noreferrer" target=3D"_blank">http://www.team.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/healeys"; rel=3D"noreferre=
r noreferrer" target=3D"_blank">http://www.team.net/pipermail/healeys</a> <=
a href=3D"http://autox.team.net/archive"; rel=3D"noreferrer noreferrer" targ=
et=3D"_blank">http://autox.team.net/archive</a><br>
<br>
<a href=3D"mailto:Healeys@autox.team.net"; rel=3D"noreferrer" target=3D"_bla=
nk">Healeys@autox.team.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys"; rel=3D"noreferre=
r noreferrer" target=3D"_blank">http://autox.team.net/mailman/listinfo/heal=
eys</a><br>
<br>
s/michael.oritt@gmail.com" rel=3D"noreferrer noreferrer" target=3D"_blank">=
http://autox.team.net/mailman/options/healeys/michael.oritt@gmail.com</a><b=
r>
<br>
</blockquote></div>
</blockquote></div>
</blockquote></div>
</blockquote></div>
</blockquote></div><br clear=3D"all"><br>-- <br><div dir=3D"ltr" class=3D"g=
mail-m_7286784059870122349gmail-m_595252486213477348gmail-m_-43605153299881=
07071gmail-m_1183269691796420998gmail-m_307167411160119781gmail-m_-70514602=
52659879810gmail-m_-1608126795714715436gmail_signature"><div dir=3D"ltr"><d=
iv><div dir=3D"ltr"><div><div dir=3D"ltr"><div><div dir=3D"ltr"><div><div d=
ir=3D"ltr"><div><font size=3D"2"><b>Steve</b></font></div></div></div></div=
></div></div></div></div></div></div></div>
</blockquote></div><br clear=3D"all"><br>-- <br><div dir=3D"ltr" class=3D"g=
mail-m_7286784059870122349gmail-m_595252486213477348gmail-m_-43605153299881=
07071gmail-m_1183269691796420998gmail-m_307167411160119781gmail-m_-70514602=
52659879810gmail_signature"><div dir=3D"ltr"><div><div dir=3D"ltr"><div><di=
v dir=3D"ltr"><div><div dir=3D"ltr"><div><div dir=3D"ltr"><div><font size=
=3D"2"><b>Steve</b></font></div></div></div></div></div></div></div></div><=
/div></div></div>
</blockquote></div>
</blockquote></div><br clear=3D"all"><br>-- <br><div dir=3D"ltr" class=3D"g=
mail-m_7286784059870122349gmail-m_595252486213477348gmail-m_-43605153299881=
07071gmail-m_1183269691796420998gmail_signature"><div dir=3D"ltr"><div><div=
dir=3D"ltr"><div><div dir=3D"ltr"><div><div dir=3D"ltr"><div><div dir=3D"l=
tr"><div><font size=3D"2"><b>Steve</b></font></div></div></div></div></div>=
</div></div></div></div></div></div>
</blockquote></div>
</blockquote></div><br clear=3D"all"><br>-- <br><div dir=3D"ltr" class=3D"g=
mail-m_7286784059870122349gmail-m_595252486213477348gmail_signature"><div d=
ir=3D"ltr"><div><div dir=3D"ltr"><div><div dir=3D"ltr"><div><div dir=3D"ltr=
"><div><div dir=3D"ltr"><div><font size=3D"2"><b>Steve</b></font></div></di=
v></div></div></div></div></div></div></div></div></div>
</blockquote></div>
</blockquote></div>
--00000000000027fe21058c62de7a--
--===============0903095030702179191==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============0903095030702179191==--
|