Re: [Healeys] BN2 Trans Dowel Bolts

[Michael MacLean via Healeys <healeys@autox.team.net>]

--===============3079180394375901415==
        boundary="----=_Part_1204143_439806588.1616893579518"

------=_Part_1204143_439806588.1616893579518
Content-Transfer-Encoding: quoted-printable

Apparently the factory thought so.Mike M

Sent from AT&T Yahoo Mail on Android=20
=20
  On Sat, Mar 27, 2021 at 3:26 PM, Perry Small via Healeys<healeys@autox.te=
am.net> wrote:  =20


More useless information. Using a regular 3/8 UNF bolt with a long enough s=
hank could potentially allow the bell housing to hang 0.001 inch low on the=
 engine back plate.=20
The play in a new input shaft bearing will allow the tip of shaft (where it=
 enters the bushing in the crank) to move, much more than 0.001. So is alig=
nment really an issue with tolerances this small?=20
P=20

Sent from my iPhone_______________________________________________

Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archiv=
e

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys

r.mike@att.net

 =20

------=_Part_1204143_439806588.1616893579518
Content-Transfer-Encoding: quoted-printable

Apparently the factory thought so.<div id=3D"yMail_cursorElementTracker_161=
6893568001">Mike M<br><br><div id=3D"ymail_android_signature"><a id=3D"ymai=
l_android_signature_link" href=3D"https://go.onelink.me/107872968?pid=3DInP=
roduct&amp;c=3DGlobal_Internal_YGrowth_AndroidEmailSig__AndroidUsers&amp;af=
_wl=3Dym&amp;af_sub1=3DInternal&amp;af_sub2=3DGlobal_YGrowth&amp;af_sub3=3D=
EmailSignature">Sent from AT&amp;T Yahoo Mail on Android</a></div> <br> <bl=
ockquote style=3D"margin: 0 0 20px 0;"> <div style=3D"font-family:Roboto, s=
ans-serif; color:#6D00F6;"> <div>On Sat, Mar 27, 2021 at 3:26 PM, Perry Sma=
ll via Healeys</div><div>&lt;healeys@autox.team.net&gt; wrote:</div> </div>=
 <div style=3D"padding: 10px 0 0 20px; margin: 10px 0 0 0; border-left: 1px=
 solid #6D00F6;"> <div dir=3D"ltr"><br></div><div dir=3D"ltr"><br></div><br=
>More useless information. Using a regular 3/8 UNF bolt with a long enough =
shank could potentially allow the bell housing to hang 0.001 inch low on th=
e engine back plate. <br>The play in a new input shaft bearing will allow t=
he tip of shaft (where it enters the bushing in the crank) to move, much mo=
re than 0.001. So is alignment really an issue with tolerances this small? =
<br>P <br><br>Sent from my iPhone__________________________________________=
_____<br>Support Team.Net <a href=3D"http://www.team.net/donate.html"; targe=
t=3D"_blank">http://www.team.net/donate.html</a><br>Suggested annual donati=
on&nbsp; $12.75<br><br>Archive: <a href=3D"http://www.team.net/pipermail/he=
aleys " target=3D"_blank">http://www.team.net/pipermail/healeys </a><a href=
=3D"http://autox.team.net/archive"; target=3D"_blank">http://autox.team.net/=
archive</a><br><br><a ymailto=3D"mailto:Healeys@autox.team.net"; href=3D"mai=
lto:Healeys@autox.team.net">Healeys@autox.team.net</a><br><a href=3D"http:/=
/autox.team.net/mailman/listinfo/healeys" target=3D"_blank">http://autox.te=
am.net/mailman/listinfo/healeys</a><br><br>Unsubscribe/Manage: <a href=3D"h=
ttp://autox.team.net/mailman/options/healeys/rrengineer.mike@att.net" targe=
t=3D"_blank">http://autox.team.net/mailman/options/healeys/rrengineer.mike@=
att.net</a><br><br> </div> </blockquote></div>
------=_Part_1204143_439806588.1616893579518--

--===============3079180394375901415==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________

Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys



--===============3079180394375901415==--