Re: [Healeys] BN2 Trans Dowel Bolts

[Michael Salter via Healeys <healeys@autox.team.net>]

--===============3454958762386024483==

--000000000000f5e95e05be8fa246

Perry I  would think that the bigger problem would be the gear alignment.
If the forward end on the input shaft were to be displaced the input gear
would engage with the laygear at an angle. .. not good.

M

On Sat., Mar. 27, 2021, 6:26 p.m. Perry Small via Healeys, <
healeys@autox.team.net> wrote:

>
>
>
> More useless information. Using a regular 3/8 UNF bolt with a long enough
> shank could potentially allow the bell housing to hang 0.001 inch low on
> the engine back plate.
> The play in a new input shaft bearing will allow the tip of shaft (where
> it enters the bushing in the crank) to move, much more than 0.001. So is
> alignment really an issue with tolerances this small?
> P
>
> Sent from my iPhone_______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation  $12.75
>
> Archive: http://www.team.net/pipermail/healeys
> http://autox.team.net/archive
>
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com
>
>

--000000000000f5e95e05be8fa246
Content-Transfer-Encoding: quoted-printable

<div dir=3D"auto">Perry I=C2=A0 would think that the bigger problem would b=
e the gear alignment.=C2=A0<div dir=3D"auto">If the forward end on the inpu=
t shaft were to be displaced the input gear would engage with the laygear a=
t an angle. .. not good.</div><div dir=3D"auto"><br></div><div dir=3D"auto"=
>M</div></div><br><div class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmai=
l_attr">On Sat., Mar. 27, 2021, 6:26 p.m. Perry Small via Healeys, &lt;<a h=
ref=3D"mailto:healeys@autox.team.net";>healeys@autox.team.net</a>&gt; wrote:=
<br></div><blockquote class=3D"gmail_quote" style=3D"margin:0 0 0 .8ex;bord=
er-left:1px #ccc solid;padding-left:1ex"><br>
<br>
<br>
More useless information. Using a regular 3/8 UNF bolt with a long enough s=
hank could potentially allow the bell housing to hang 0.001 inch low on the=
 engine back plate. <br>
The play in a new input shaft bearing will allow the tip of shaft (where it=
 enters the bushing in the crank) to move, much more than 0.001. So is alig=
nment really an issue with tolerances this small? <br>
P <br>
<br>
Sent from my iPhone_______________________________________________<br>
rer noreferrer" target=3D"_blank">http://www.team.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/healeys"; rel=3D"noreferre=
r noreferrer" target=3D"_blank">http://www.team.net/pipermail/healeys</a> <=
a href=3D"http://autox.team.net/archive"; rel=3D"noreferrer noreferrer" targ=
et=3D"_blank">http://autox.team.net/archive</a><br>
<br>
<a href=3D"mailto:Healeys@autox.team.net"; target=3D"_blank" rel=3D"noreferr=
er">Healeys@autox.team.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys"; rel=3D"noreferre=
r noreferrer" target=3D"_blank">http://autox.team.net/mailman/listinfo/heal=
eys</a><br>
<br>
s/michaelsalter@gmail.com" rel=3D"noreferrer noreferrer" target=3D"_blank">=
http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com</a><b=
r>
<br>
</blockquote></div>

--000000000000f5e95e05be8fa246--

--===============3454958762386024483==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________

Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys



--===============3454958762386024483==--