tigers
[Top] [All Lists]

Re: [Tigers] vent window won't come out

To: <CoolVT@aol.com>, <Rollright@aol.com>, <tigers@Autox.Team.Net>
Subject: Re: [Tigers] vent window won't come out
From: " Ron Fraser" <rfraser@bluefrog.com>
Date: Sun, 1 Apr 2012 13:27:25 -0400
Cc: onegonefish@comcast.net, todbrown@roadrunner.com
Delivered-to: tigers-archive@autox.team.net
Delivered-to: tigers@autox.team.net
List-archive: <http://autox.team.net/pipermail/tigers>
List-help: <mailto:tigers-request@autox.team.net?subject=help>
List-id: Sunbeam Tigers <tigers.autox.team.net>
List-post: <mailto:tigers@autox.team.net>
List-subscribe: <http://autox.team.net/mailman/listinfo/tigers>, <mailto:tigers-request@autox.team.net?subject=subscribe>
List-unsubscribe: <http://autox.team.net/mailman/options/tigers>, <mailto:tigers-request@autox.team.net?subject=unsubscribe>
Thread-index: Ac0QKQ9MTvnWuiRdRJa4Xj2z5SuOOQAAeRyA engine=2.50.10432:5.6.7498,1.0.260,0.0.0000 definitions=2012-04-01_03:2012-03-30,2012-04-01,1970-01-01 signatures=0 spamscore=0 ipscore=0 suspectscore=2 phishscore=0 bulkscore=0 adultscore=0 classifier=spam adjust=0 reason=mlx scancount=1 engine=6.0.2-1203120001 definitions=main-1204010193
Mark
    This is a 2 piece "U" channel.   The bottom steel channel bolts to the
door I believe with 3 bolts; that is where you do the adjustment.   The
upper chrome channel slides onto or over the lower channel.    There is a
spring clip on the lower channel but I think it is mostly a guide and Stop.
The 2 channels may have locked together some.   Remove the door panel and
take a look.   Maybe some oil on the channels is needed to get them to come
apart. ?

As you state its been a long time since I was in there too.

This is where updated Tech tips with pictures would really help.

Good luck

Ron Fraser

-----Original Message-----
From: CoolVT@aol.com [mailto:CoolVT@aol.com]
Sent: Sunday, April 01, 2012 1:01 PM
To: Rollright@aol.com; rfraser@bluefrog.com; tigers@Autox.Team.Net
Cc: onegonefish@comcast.net; todbrown@roadrunner.com
Subject: Re: [Tigers] vent window won't come out



It's been a long time, but I thought there was something at the bottom. I'm
pretty sure I remember doing an adjustment down there.
Mark

In a message dated 4/1/2012 12:58:41 P.M. Eastern Daylight Time,
Rollright@aol.com writes:

Ron,

After receiving your instructions, I inspected one of the vent window
assemblies on my bench for the fasteners that you described and there are
the
six tiny screws, and then the bigger screws in the chrome finisher. That's
it.  No more fasteners at all.

Got the car back yesterday as I mentioned previously, took out the two #10
screws a few moments ago and
pulled hard several times on the vent assy......no go. firmly rocked it and
pulled. Nope.

What do you think it might be?

Jim  Armstrong
Mk 1A
382002083
LRXFE
_______________________________________________

tigers@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: http://autox.team.net/mailman/options/tigers/coolvt@aol.com
_______________________________________________

tigers@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: 
http://autox.team.net/mailman/options/tigers/tigers-archive@autox.team.net



<Prev in Thread] Current Thread [Next in Thread>