Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[6pack\]\s+U\-joint\s+removal\,\s+last\s+trick\s+in\s+my\s+book\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[6pack\]\s+U\-joint\s+removal\,\s+last\s+trick\s+in\s+my\s+book\s*$/: 6 ]

Total 6 documents matching your query.

1. [6pack] U-joint removal, last trick in my book (score: 1): Author: "John North" <johncnorth@gmail.com>; Date: Thu, 21 Feb 2008 21:49:45 -0500; Gone through all my tricks, "tapping", beating, two sockets in a vise etc trying to get the last prop shaft u-joint out of the flange. Last night I heated it up with a propane torch, still won't move; /html/6pack/2008-02/msg00182.html (6,992 bytes)
2. Re: [6pack] U-joint removal, last trick in my book (score: 1): Author: Robert Lang <lang@isis.mit.edu>; Date: Fri, 22 Feb 2008 10:13:33 -0500 (EST); Will it damage the flange? The answer depends on how hot. Heat that baby to cherry red and you might as well throw the whole thing out. You should never need heat for this job. Get the cups out as fa; /html/6pack/2008-02/msg00189.html (8,537 bytes)
3. Re: [6pack] U-joint removal, last trick in my book (score: 1): Author: Ed Bratt <bratt@sasktel.net>; Date: Fri, 22 Feb 2008 11:50:25 -0600; When faced with an impossible task--use penetrating oil. Use real penetrating oil, not cheap junk solvent sprays. Just apply two drops. Let it sit for half a day. Apply two more drops. Repeat mornin; /html/6pack/2008-02/msg00199.html (8,050 bytes)
4. Re: [6pack] U-joint removal, last trick in my book (score: 1): Author: Robert Lang <lang@isis.mit.edu>; Date: Fri, 22 Feb 2008 14:27:02 -0500 (EST); [stuff deleted] Heat can also change the "temper" of the metal which is really bad for forged parts (like your axle yokes). I can always tell if a yoke has beed heated (either with a torch or from th; /html/6pack/2008-02/msg00202.html (7,715 bytes)
5. Re: [6pack] U-joint removal, last trick in my book (score: 1): Author: tr6taylor@webtv.net (Sally or Dick Taylor); Date: Fri, 22 Feb 2008 23:04:26 -0800; John N.--If you are still fighting with the stubborn U-joint bearings, I'd suggest you use a shock treatment, rather than a press-out with sockets. Almost the same, but use a socket slightly smaller; /html/6pack/2008-02/msg00209.html (9,115 bytes)
6. Re: [6pack] U-joint removal, last trick in my book (score: 1): Author: "Rick" <patton@suscom-maine.net>; Date: Sat, 23 Feb 2008 02:12:34 -0500; Hi John, I don't want to discourage you doing the job, but I replace u-joints at my auto parts store everyday and it usually runs about $15 per joint. You might want to make a couple of phone calls e; /html/6pack/2008-02/msg00210.html (7,814 bytes)

Current List: 1 - 6
Page: [1]