Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Grease\s+Nipple\s+Lower\s+Wishbone\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Grease\s+Nipple\s+Lower\s+Wishbone\s*$/: 9 ]

Total 9 documents matching your query.

1. Grease Nipple Lower Wishbone (score: 1): Author: Unknown; Date: Tue, 24 Oct 2000 21:22:57 -0400; Has anyone retapped the threads for the grease nipple that goes on the lower wishbone for a TR3? My threading has gone bad and I can't fit a new grease nipple on the arm. As far as my measurements go; /html/triumphs/2000-10/msg00929.html (7,534 bytes)
2. RE: Grease Nipple Lower Wishbone (score: 1): Author: Unknown; Date: Wed, 25 Oct 2000 09:42:38 -0700; I'm pretty sure the thread is actually 1/8-27 NPT (National Pipe Tapered). Should be able to buy a tap at most hardware stores, Sears, etc. You'll likely either have to grind the end of the tap off,; /html/triumphs/2000-10/msg00950.html (7,600 bytes)
3. Re: Grease Nipple Lower Wishbone (score: 1): Author: Unknown; Date: Wed, 25 Oct 2000 18:08:30 -0400; I bought a tap for this application a few years ago and have used it on all lower wishbones with success. Its a 1/8-28 BSSP. British Standard ??? Pipe? Ed Woods; /html/triumphs/2000-10/msg00967.html (7,410 bytes)
4. Re: Grease Nipple Lower Wishbone (score: 1): Author: Unknown; Date: Wed, 25 Oct 2000 23:00:06 EDT; Found a site with the thread data, it's a little smashed together down there, but you'll see the 1/8-28 listed. ( for some reason the column headings went vertical, and the data stayed horizontal whe; /html/triumphs/2000-10/msg00980.html (7,904 bytes)
5. Re: Grease Nipple Lower Wishbone (score: 1): Author: Unknown; Date: Thu, 26 Oct 2000 10:28:55 -0400charset="iso-8859-1"; I'm pretty sure the grease fitting has a pipe thread. It's most likely a 1/8" pipe thread. This is a taper thread with 27 tpi, (not 28) and has a pitch diameter at the smallest end of the taper of .3; /html/triumphs/2000-10/msg00993.html (8,728 bytes)
6. Re: Grease Nipple Lower Wishbone (score: 1): Author: Unknown; Date: Thu, 26 Oct 2000 21:14:06 -0400; Picked up a 1/8"-27 pipe tap today at Sears and it worked perfectly. Thanks Scott; /html/triumphs/2000-10/msg01016.html (9,324 bytes)
7. Re: Grease Nipple Lower Wishbone (score: 1): Author: Unknown; Date: Thu, 26 Oct 2000 21:16:20 -0400; Beg to differ. I dug out the tap for this application. It's marked 1/8-28 BSPP G HS 55 degrees. It is not tapered. I would guess that the second "P" is for "plug" as in plug tap, which this one is. A; /html/triumphs/2000-10/msg01017.html (8,263 bytes)
8. Re: Grease Nipple Lower Wishbone (score: 1): Author: Unknown; Date: Thu, 26 Oct 2000 21:18:13 -0400; Beg to differ. I dug out the tap for this application. It's marked 1/8-28 BSPP G HS 55 degrees. It is not tapered. I would guess that the second "P" is for "plug" as in plug tap, which this one is. A; /html/triumphs/2000-10/msg01020.html (8,241 bytes)
9. Re: Grease Nipple Lower Wishbone (score: 1): Author: Unknown; Date: Thu, 26 Oct 2000 21:46:59 -0400charset="iso-8859-1"; You may be right, although Mr Suhring just sent me an e-mail saying that the 1/8 NPT tap worked perfectly. I just assumed that, as most of the other fasteners on the car are Unified then the grease f; /html/triumphs/2000-10/msg01021.html (9,660 bytes)

Current List: 1 - 9
Page: [1]