Always being out of time with too many cars to service (rebuild) I used to
just put the torch to the bushing, warm it really good then drop it into a
dish of oil. Never had a problem in this area.
----- Original Message -----
From: "Greg Solow" <gregmogdoc@surfnetusa.com>
To: "MadMarx" <tr4racing@googlemail.com>; <fot@autox.team.net>
Sent: Saturday, April 05, 2008 10:58 AM
Subject: Re: [Fot] Crank end Bush grease or no grease?
> Grease could have a tendency to come out and get on the clutch disc. It
> may
> also have a tendency to plug the pores of the oilite bushing. This is just
> a
> guess. I try to follow what the designing engineers appear to have done.
> If
> there is not an obvious fault in their design. For the most part, the TR
> engineers seem to have done a good job with what they did. By using an
> Oilite bush in the pilot bushing location, it is clear that they intended
> a
> very small amount of "oil" to be the lubricant used there.
> Greg Solow
>
> ----- Original Message -----
> From: "MadMarx" <tr4racing@googlemail.com>
> To: "Greg Solow" <gregmogdoc@surfnetusa.com>; <fot@autox.team.net>
> Sent: Saturday, April 05, 2008 9:52 AM
> Subject: Re: [Fot] Crank end Bush grease or no grease?
>
>
> why no grease?
> I have used grease since and never had any trouble....so why no grease?
>
> Cheers
> Chris
>
> ----- Original Message -----
> From: "Greg Solow" <gregmogdoc@surfnetusa.com>
> To: "Steven Belfer" <colordog.1@earthlink.net>; "FOT" <fot@autox.team.net>
> Sent: Saturday, April 05, 2008 2:22 AM
> Subject: Re: [Fot] Crank end Bush grease or no grease?
>
>
>> The pilot bushing is captured in place by the flywheel. It should be
>> impregnated with 10 sae motor oil by soaking it in oil for 24 hours or
>> putting the bushing on top of one thumb so your thumb fills covers the
>> bottom of the center hole. Then fill the hole with oil. Then put your
>> other
>> thumb on top of the hole and squeeze both thumbs together until you can
>> see
>> oil come out through the pores on the outside of the bushing. This will
>> ensure that the pores withing the bushing have a resevoir of oil to keep
>> the
>> bushing and the input shaft lubricated. wipe off the excess oil and slide
>> it
>> into the crankshaft, Then install the flywheel. Grease should not be used
>> in
>> this location!
>>
>> Greg Solow
>>
>> ----- Original Message -----
>> From: "Steven Belfer" <colordog.1@earthlink.net>
>> To: "FOT" <fot@autox.team.net>
>> Sent: Friday, April 04, 2008 4:53 PM
>> Subject: [Fot] Crank end Bush grease or no grease?
>>
>>
>> > You know that little brash bush that sits in the back end of the
>> > crankshaft?
>> > On my TR3 it sits in there nicely, it's not tight but turn freely?
>> >
>> > Does it get a dab of grease or oil? or could that possibly foul the
>> > clutch?
>> >
>> > ~Steve
>> > _______________________________________________
>> > http://www.team.net/donate.html
>> >
>> > Fot mailing list
>> > Fot@autox.team.net
>> > http://autox.team.net/mailman/listinfo/fot
>> >
>> > You are subscribed as gregmogdoc@surfnetusa.com
>> _______________________________________________
>> http://www.team.net/donate.html
>>
>> Fot mailing list
>> Fot@autox.team.net
>> http://autox.team.net/mailman/listinfo/fot
>>
>> You are subscribed as tr4racing@googlemail.com
> _______________________________________________
> http://www.team.net/donate.html
>
> Fot mailing list
> Fot@autox.team.net
> http://autox.team.net/mailman/listinfo/fot
>
> You are subscribed as kaskas@cox.net
_______________________________________________
http://www.team.net/donate.html
Fot mailing list
Fot@autox.team.net
http://autox.team.net/mailman/listinfo/fot
|