spridgets
[Top] [All Lists]

Re: fuel gauge questions

To: Bryan.Vandiver@Eng.Sun.COM, boxweed@thebest.net
Subject: Re: fuel gauge questions
From: Bryan Vandiver <Bryan.Vandiver@Eng.Sun.COM>
Date: Wed, 11 Aug 1999 14:55:41 -0700 (PDT)
Cc: spridgets@autox.team.net
Reply-to: Bryan Vandiver <Bryan.Vandiver@Eng.Sun.COM>
Sender: owner-spridgets@autox.team.net
Bob,

I really appreciate your input, but I really think we might be talking apples 
and 
oranges here.  The coils in my fuel guage are identical in size and shape, and 
are 
positioned symmetrically to create a magnetic field. the top of each coil has a 
metal 
'tab' about 1/2" wide with a semi circular cut that is directly opposed to a 
wedge 
shaped piece with a radius that mirrors that of the two metal peices on top of 
the 
coils, that is mounted to the needle pivot.

What is the part number of the guage you are referring to??
Mine is an orginal bugeye gauge (I'll check the exact part number as soon as I 
get a 
chance, and let you know what it is).

Thanks - Bryan


The needle itself has only the typical needle spring on it, with no other 
mechanism
>To: "Bryan Vandiver" <Bryan.Vandiver@eng.sun.com>
>Cc: "spridgets list" <spridgets@autox.team.net>
>Subject: Re: fuel gauge questions
>MIME-Version: 1.0 charset="iso-8859-1"
>X-Priority: 3
>X-MSMail-Priority: Normal
>X-MimeOLE: Produced By Microsoft MimeOLE V4.72.3110.3
>
>Bryan,
>
>First, nothing should be grounded to the fuel gauge case.  Second, your
>gauge is a thermostatic type, which means that as the current passes through
>the insulated coil, the coil heats up, which causes a bimetal strip that
>should be either running through the center of the coil or somewhere near
>the coil (but not necessarily touching the coil) to heat up also.  This
>bimetal strip is attached to the needle.  As one side of this bimetal piece
>heats up faster than the other side, it bends, which causes the needle to
>move, indicating the amount of fuel.  The path of the current should be from
>the battery to the "B" terminal, then to the first (left) coil, (which is
>simply a resistor to reduce the voltage) then to the heating (right)coil,
>and finally to the "T" terminal.  So, one end of the wire on the left coil
>should be attached to the "B" terminal, and the other end should be attached
>to the right coil.  The other end of the insulated right coil should be
>attached to the "T" terminal.  The needle itself should not be attached to
>any wires.  Hope this helps.
>
>Bob
>-----Original Message-----
>From: Bryan Vandiver <Bryan.Vandiver@Eng.Sun.COM>
>To: boxweed@thebest.net <boxweed@thebest.net>
>Date: Tuesday, August 10, 1999 2:40 PM
>Subject: Re: fuel gauge questions
>
>
>>Bob,
>>
>>Thanks.
>>The back of my gauge is marked  B and T.
>>As far as the series connection goes..
>>Is the left coil 'grounded to the case through it's screw mounting??, or
>does
>>each coil have a wire soldered to each side of the needle assembly?
>>Looking at the inside of the gauge from the front, it appears the left coil
>has
>>only one (1) wire coming off it (should there be two?)
>>If there is only one wire, I assume this should be soldered to the point on
>top
>>of the right coil, and the 'wire comming off the insulated tab on the right
>coil
>>is soldered to the point on the rt side of the needle assembly??
>>
>>I'll try doing a primative diagram:
>>
>>  | needle |
>>  ----------
>>   \      /
>>   O------O
>>
>>   OR
>>
>>   | needle |
>>   ----------
>>           /
>>gnd-O------O
>>
>>Thanks
>>Bryan
>>
>>
>>>To: "Bryan Vandiver" <Bryan.Vandiver@eng.sun.com>
>>>Cc: "spridgets list" <spridgets@autox.team.net>
>>>Subject: Re: fuel gauge questions
>>>MIME-Version: 1.0
>>>Content-Transfer-Encoding: 7bit
>>>X-Priority: 3
>>>X-MSMail-Priority: Normal
>>>X-MimeOLE: Produced By Microsoft MimeOLE V4.72.3110.3
>>>
>>>If the two terminals on the back of the fuel gauge are marked with a "B"
>for
>>>battery, and a "T" for tank, then the two coils should be attached to each
>>>other in series.  If there are no markings on the terminals on the back of
>>>the fuel gauge, then the two coils should be connected in parallel.
>>>
>>>Bob
>>>-----Original Message-----
>>>From: Bryan Vandiver <Bryan.Vandiver@Eng.Sun.COM>
>>>To: spridgets@autox.team.net <spridgets@autox.team.net>
>>>Date: Monday, August 09, 1999 6:43 PM
>>>Subject: fuel gauge questions
>>>
>>>
>>>>Hello everyone,
>>>>
>>>>Does anyone have information on the internal wiring of the bugeye fuel
>>>gauge??
>>>>My Gauge wasn't working at all, so I thought I'd open it up to find out
>>>why..
>>>>
>>>>There are two small 'coils' locate on either side of the needle assembly
>>>inside
>>>>the gauge, but the 'hair fine' wires that were soldered to the needle
>>>assembly
>>>>have been broken off. Apparently a previous owner had unscrewed the coil
>>>>assmblies from the back of the case, and in the process the coils
>rotated,
>>>>breaking off the wires. the coils still look OK, and it looks like a
>>>'simple
>>>>matter to resolder them, unfortunately I can tell which wire goes where.
>I
>>>>assume the two coils were attached to each other, but all I see is two
>>>loose
>>>>wires...
>>>>Any ideas???
>>>>
>>>>Regards,
>>>>Bryan
>>>
>


<Prev in Thread] Current Thread [Next in Thread>