spridgets
[Top] [All Lists]

Re: fuel gauge questions

To: "Bryan Vandiver" <Bryan.Vandiver@Eng.Sun.COM>
Subject: Re: fuel gauge questions
From: "Wiedemeyer" <boxweed@thebest.net>
Date: Wed, 11 Aug 1999 09:09:44 -0400
Cc: "spridgets list" <spridgets@autox.team.net>
Reply-to: "Wiedemeyer" <boxweed@thebest.net>
Sender: owner-spridgets@autox.team.net
Bryan,

It occurred to me that the insulated coil may actually be the resistor, and
the other coil may be the heating coil.  If so, the metal piece that
attaches to the needle would be going through (or lie near) the bare coil
instead.  If this is the case, then the connections would be:  Battery to
"B" terminal, then "B" terminal to insulated coil, then insulated coil to
other coil, then other coil to "T" terminal.  The main point is that the "B"
terminal has to connect to the resistor before connecting to the heating
coil or the heating coil will get too hot and "fry" itself.

Bob
-----Original Message-----
From: Wiedemeyer <boxweed@thebest.net>
To: Bryan Vandiver <Bryan.Vandiver@Eng.Sun.COM>
Cc: spridgets list <spridgets@autox.team.net>
Date: Tuesday, August 10, 1999 11:12 PM
Subject: Re: fuel gauge questions


>Bryan,
>
>First, nothing should be grounded to the fuel gauge case.  Second, your
>gauge is a thermostatic type, which means that as the current passes
through
>the insulated coil, the coil heats up, which causes a bimetal strip that
>should be either running through the center of the coil or somewhere near
>the coil (but not necessarily touching the coil) to heat up also.  This
>bimetal strip is attached to the needle.  As one side of this bimetal piece
>heats up faster than the other side, it bends, which causes the needle to
>move, indicating the amount of fuel.  The path of the current should be
from
>the battery to the "B" terminal, then to the first (left) coil, (which is
>simply a resistor to reduce the voltage) then to the heating (right)coil,
>and finally to the "T" terminal.  So, one end of the wire on the left coil
>should be attached to the "B" terminal, and the other end should be
attached
>to the right coil.  The other end of the insulated right coil should be
>attached to the "T" terminal.  The needle itself should not be attached to
>any wires.  Hope this helps.
>
>Bob
>-----Original Message-----
>From: Bryan Vandiver <Bryan.Vandiver@Eng.Sun.COM>
>To: boxweed@thebest.net <boxweed@thebest.net>
>Date: Tuesday, August 10, 1999 2:40 PM
>Subject: Re: fuel gauge questions
>
>
>>Bob,
>>
>>Thanks.
>>The back of my gauge is marked  B and T.
>>As far as the series connection goes..
>>Is the left coil 'grounded to the case through it's screw mounting??, or
>does
>>each coil have a wire soldered to each side of the needle assembly?
>>Looking at the inside of the gauge from the front, it appears the left
coil
>has
>>only one (1) wire coming off it (should there be two?)
>>If there is only one wire, I assume this should be soldered to the point
on
>top
>>of the right coil, and the 'wire comming off the insulated tab on the
right
>coil
>>is soldered to the point on the rt side of the needle assembly??
>>
>>I'll try doing a primative diagram:
>>
>>  | needle |
>>  ----------
>>   \      /
>>   O------O
>>
>>   OR
>>
>>   | needle |
>>   ----------
>>           /
>>gnd-O------O
>>
>>Thanks
>>Bryan
>>
>>
>>>To: "Bryan Vandiver" <Bryan.Vandiver@eng.sun.com>
>>>Cc: "spridgets list" <spridgets@autox.team.net>
>>>Subject: Re: fuel gauge questions
>>>MIME-Version: 1.0
>>>Content-Transfer-Encoding: 7bit
>>>X-Priority: 3
>>>X-MSMail-Priority: Normal
>>>X-MimeOLE: Produced By Microsoft MimeOLE V4.72.3110.3
>>>
>>>If the two terminals on the back of the fuel gauge are marked with a "B"
>for
>>>battery, and a "T" for tank, then the two coils should be attached to
each
>>>other in series.  If there are no markings on the terminals on the back
of
>>>the fuel gauge, then the two coils should be connected in parallel.
>>>
>>>Bob
>>>-----Original Message-----
>>>From: Bryan Vandiver <Bryan.Vandiver@Eng.Sun.COM>
>>>To: spridgets@autox.team.net <spridgets@autox.team.net>
>>>Date: Monday, August 09, 1999 6:43 PM
>>>Subject: fuel gauge questions
>>>
>>>
>>>>Hello everyone,
>>>>
>>>>Does anyone have information on the internal wiring of the bugeye fuel
>>>gauge??
>>>>My Gauge wasn't working at all, so I thought I'd open it up to find out
>>>why..
>>>>
>>>>There are two small 'coils' locate on either side of the needle assembly
>>>inside
>>>>the gauge, but the 'hair fine' wires that were soldered to the needle
>>>assembly
>>>>have been broken off. Apparently a previous owner had unscrewed the coil
>>>>assmblies from the back of the case, and in the process the coils
>rotated,
>>>>breaking off the wires. the coils still look OK, and it looks like a
>>>'simple
>>>>matter to resolder them, unfortunately I can tell which wire goes where.
>I
>>>>assume the two coils were attached to each other, but all I see is two
>>>loose
>>>>wires...
>>>>Any ideas???
>>>>
>>>>Regards,
>>>>Bryan
>>>
>


<Prev in Thread] Current Thread [Next in Thread>