tigers
[Top] [All Lists]

Re: [Tigers] Pulley Line-up

To: robert jaarsma <64venezia@gmail.com>, tigers@autox.team.net
Subject: Re: [Tigers] Pulley Line-up
From: David or Gary Franchi <wwwdg@webtv.net>
Date: Fri, 28 Jun 2013 21:35:02 GMT FILETIME=[5945A6C0:01CE7447]
Delivered-to: mharc@autox.team.net
Delivered-to: tigers@autox.team.net
Robert, It is posible you don't have the special Tiger bracket, since you said 
it never lined up originally.

I have this saved from an old post on the diffrence between a Tiger Generator 
bracket and a Ford bracket. 
I took a few photos comparing them. This Tiger bracket is only marked with a 
Triangle with a "C"or "O" inside and a "1" next to it. The Tiger bracket offset 
is about 11/16" closer to the head and it is shaped a little differently. 

David Franchi

Misc. bracket pictures, Tiger is always on the left.

http://pic50.picturetrail.com/VOL439/2051017/23401185/398477547.jpg 
--

http://pic50.picturetrail.com/VOL439/2051017/23401185/398477548.jpg 
--

http://pic50.picturetrail.com/VOL439/2051017/23401185/398477549.jpg 
--

http://pic50.picturetrail.com/VOL439/2051017/23401185/398477550.jpg 
--

http://pic50.picturetrail.com/VOL439/2051017/23401185/398477551.jpg 
--

Tiger and Ford markings.
http://pic50.picturetrail.com/VOL439/2051017/23401185/398477552.jpg 
--

Tiger marking close-up.

http://pic50.picturetrail.com/VOL439/2051017/23401185/398477553.jpg
--


-----Original Message-----
From: robert jaarsma
Sent: Friday, June 28, 2013 5:05 AM
To: tigers@autox.team.net
Subject: [Tigers] Pulley Line-up

My Tiger with a 289 needed a new water pump, so I got the one from Sunbeam
Specialties. No surprises there. Pulley lined up perfectly with the balancer
pulley.

My generator was still ok, but I estimated its life would not be too much
longer. So for a while I thought about swapping it for an alternator. It
never really lined up perfectly. But during 20 years, never gave a problem
either. Possibly shortened the water pumps life? .

Since there was recently a discussion about alternators, I decide to take
the plunge and make it easy on myself and I bought the Powermaster unit. My
alternator pulley is off by > with the water pump pulley! The way its
pulley is mounted it has a heavy rim on the outside, which throws the
v-groove off by maybe 1/8. So if I turn it around, I will still be off by
>-1/8= 5/8. All powermaster other mounting dimensions are identical, 6
between the ears, to straddle the original mounting arm. Now I suspect the
original mounting bracket. 1). I could put spacer between it and the engine
block, the bring the alternator forwards. However the dipstick doesnt give
me much room. 2). I could bring the alternator forwards by putting the rear
ear on the front side of the bracket and add a spacer at the front ear. But
the alternator ear would not clear the rib of the cast Tiger mounting
bracket. Not an elegant solution. But then, how could the original cast
Tiger bracket be off by that much? If it was fabricated it possibly could
bend, but not a casting. Reyer and I measured everything again tonight, but
we can not see whats wrong. Any ideas?

Just one more thing besides my electrical problem: the white wire from
ignition switch to tach to coil resistor filled itself with Lucas smoke.
Why?? All insulation half burned. No obvious short I could see. I am almost
ready to take it all apart and rewire the whole car. Any body has any
ideas?? thanks, Robert Jaarsma
_______________________________________________

tigers@autox.team.net

Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/wwwdg@webtv.net
_______________________________________________

tigers@autox.team.net

Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/mharc@autox.team.net


<Prev in Thread] Current Thread [Next in Thread>