fot
[Top] [All Lists]

[Healeys] Belleville washers in BN2 steering box

Subject: [Healeys] Belleville washers in BN2 steering box
From: bspidell at comcast.net (Bob Spidell)
Date: Thu, 12 Jan 2017 09:04:34 -0800
References: <5c4d20a5-d2ec-b119-8b67-e3a3923683eb@comcast.net> <001501d26b8e$fc7f3990$f57dacb0$@hunterbane.com>
Well, I went ahead and ordered from Moss.  I did a cursory check of the 
interwebs didn't turn up anything of those dimensions here:

https://www.mcmaster.com/#standard-washers/=15uvd84

and here:

http://www.keybellevilles.com/bellevilles/sampleCatalog.php?gclid=CMCHjPHOuNECFQGRfgodVAoFuA

and others, and I need to get this car back together before I start 
losing the little bits.   FWIW, SC Parts and AH Spares have them at a 
more reasonable price--esp. with the current exchange rate--but with VAT 
and shipping it's not a massive savings.

My thanks to Olin, Bob and others who responded; if I come across these 
in this size I'll make a note for future reference. Now, at least, I 
know what they're for and how to stack them.

Bob


On 1/10/2017 2:14 PM, Olin Brimberry wrote:
> Bob,
>
> I figured height of the spring was also important, so I put 2 together and 
> measured the height with calipers
> Height of 2 washers: 0.100 inches
> Height of 1 washer: 0.050 inches
> Thickness of washer: 0.025 inches
> Checking the previous diameter dimensions with a caliper, I get:
>   
> ID: 1.057 inches
> OD: 1.5 inches
>
> I suspect that the ID is originally spec'd to be 1-1/16" but because of the 
> slight "spring", the diameter is slightly less.  Good luck
>
> Olin K. Brimberry, PE
> Principal Engineer
> obrimberry at hunterbane.com
> Office - 919.803.4274
> Mobile - 919.522.1608
>
> HunterBane Engineering, PLLC
> PO Box 10314
> Raleigh, NC 27605
> 3306 Alamance Drive
> Raleigh, NC 27609
>
>
>
> -----Original Message-----
> From: Olin Brimberry [mailto:obrimberry at hunterbane.com]
> Sent: Tuesday, January 10, 2017 4:34 PM
> To: 'Bob Spidell'<bspidell at comcast.net>; 'Healeys'<healeys at 
> autox.team.net>
> Subject: RE: [Healeys] Belleville washers in BN2 steering box
>
> I just pulled mine out of a steering box I am rebuilding, and yes there are 6 
> positioned as such: ()()() Where only the outer edges touch.  The dimensions 
> are as follows:
>
> ID: 1-1/16
> OD: 1-1/2
> Pictures of the measurements are attached for verification purposes.
>
> The washers were loose on the shaft, but I think the closer tolerance is 
> going to be on the OD side.
>
> Olin K. Brimberry, PE
> Principal Engineer
> obrimberry at hunterbane.com
> Office - 919.803.4274
> Mobile - 919.522.1608
>
> HunterBane Engineering, PLLC
> PO Box 10314
> Raleigh, NC 27605
> 3306 Alamance Drive
> Raleigh, NC 27609
>
>
>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/healeys/attachments/20170112/3b7b9745/attachment.html>

<Prev in Thread] Current Thread [Next in Thread>