This is a multipart message in MIME format.
--===============7212010651841810864==
boundary="----=_NextPart_000_0019_01D6BEB0.2EC2FAE0"
Content-Language: nl
This is a multipart message in MIME format.
------=_NextPart_000_0019_01D6BEB0.2EC2FAE0
charset="UTF-8"
Content-Transfer-Encoding: quoted-printable
I have tested the starter outside of the car. Bendix works well, but motor =
runs poorly with lots of sparking over the brushes.
So I took your advice and it is now at the local repair shop. They=E2=80=99=
ll disassemble it first, in order to see it is feasible to do a repair, or =
a new starter is better.
Cheers,
Hans
Van: Mgs <mgs-bounces@autox.team.net> Namens Richard Lindsay
Verzonden: zondag 15 november 2020 14:57
Aan: Hans Duinhoven <h.duinhoven@planet.nl>
CC: mglist <mgs@autox.team.net>; MGB-Yahoo <mg-mgb@yahoogroups.com>
Onderwerp: Re: [Mgs] Slow cranking, was Siphoning Gas
My vote is to have your local shop do the rebuild. Turn the commutator on t=
he lathe and replace the brushes.
anet.nl> > wrote:
I measured the voltage on the posts while cranking =3D 10,5 volts. It is on=
a digital meter, so I wonder if that=E2=80=99s a good value.
The same value is measured on the starter ingoing post.
So no tension loss on the electrical circuits.
Now there is a discussion:
Repair the starter or buy a new one.
High torque starter =3D =E2=82=AC 325,00, which is pricy
Original starter on exchange base =3D =E2=82=AC 200,00
New starter Powerlite =3D =E2=82=AC 239,00
New starter looking like a Lucas (white labelled) =3D =E2=82=AC 135,00
https://www.octagonparts.nl/product-categorie/mgb/electrical-mgb/starting-s=
ystem-mgb-electrical-mgb/
https://www.angloparts.com/en/catalogues/part/26883/082.024
There is a local electrical car parts repair shop, where the alternator has=
been repaired +/- 10 years ago.
They did a good job.
I assume they can fix the starter as well, but what is better =E2=80=93 a n=
ew one (Angloparts =3D =E2=82=AC 152 or =E2=82=AC 135,00 at octagonparts) o=
r have the original repaired=E2=80=A6
Cheers,
Hans
com> >
Verzonden: dinsdag 10 november 2020 11:41
Onderwerp: Re: [Mgs] Slow cranking, was Siphoning Gas
Yes, measure the voltage right on the battery posts (adding the two voltage=
s together if twin 6v batteries) when cranking, then compare that with the =
voltage at the battery cable stud on the solenoid and starter body when cra=
nking. The difference between the two is what is being lost in the connect=
ions, a volt or so is normal but it shouldn't be much more than that.
If you get much less than 10v at the battery posts then that is the problem=
=2E
PaulH.
----- Original Message -----
Next job is the slow starter motor.
I already cleaned the battery posts clamps and the post of the battery to c=
hassis cable.
Also cleaned thoroughly the chassis to engine cable.
Nothing helped so far.
So next will be verifying the battery voltage when cranking. I assume it wi=
ll be o.k. as the battery is new.
Following step will be measuring the voltage over the starter motor +12V to=
the engine.
When o.k., the starter is suspect. As it never was overhauled, this is logi=
cal.
Nice winter job.
Namens Dan DiBiase
Verzonden: donderdag 22 oktober 2020 22:26
il.com> >
Onderwerp: Re: [Mgs] Siphoning Gas
OMG, duh! Thanks to all that replied with this excellent (and obvious, now!=
) advice..............................
Dan D
http://dandibiase.cbintouch.com/
On Thu, Oct 22, 2020 at 4:13 PM Richard Lindsay <richardolindsay@gmail.com =
I had the same problem. I disconnected the fuel hose, added a a long bit of=
hose and with the coil disconnected, used the fuel pump to pump old fuel i=
nto jugs.
n.dibiase@gmail.com> > wrote:
Hi all.... My '76B, which was off the road for 5 years, was recently return=
ed to me from the shop. They added some new gas but did not siphon out the =
5 year old gas (which was just under 1/2 tank when I had it towed in. The c=
ar is running pretty rough so I want to siphon out most of the gas before I=
fill it up. It is currently showing as just under 1/2 tank, so around 6 ga=
llons or a little less (assuming gauge accuracy).
I was able to pump out about 2 gallons but am wondering if the interior of =
the tank is baffled, as I can't seem to move the hose beyond a certain area=
and it's not sucking up any additional gas. Would really like to remove a =
couple more gallons before I fill it up.
Thx,
Dan D
'76B- Getting There
'65B - Waiting It's Turn
Central NJ USA
http://dandibiase.cbintouch.com/
_______________________________________________
Archive: http://www.team.net/pipermail/mgs http://autox.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/mgs/richardolindsay@gmai=
l.com
<https://www.avast.com/sig-email?utm_medium=3Demail&utm_source=3Dlink&utm_=
campaign=3Dsig-email&utm_content=3Demailclient>
Virusvrij. <https://www.avast.com/sig-email?utm_medium=3Demail&utm_source=
=3Dlink&utm_campaign=3Dsig-email&utm_content=3Demailclient> www.avast.com
_____
_______________________________________________
Archive: http://www.team.net/pipermail/mgs http://autox.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/mgs/paulhunt73@virginmed=
ia.com
_______________________________________________
Archive: http://www.team.net/pipermail/mgs http://autox.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/mgs/richardolindsay@gmai=
l.com
--
Dit e-mailbericht is gecontroleerd op virussen met Avast antivirussoftware.=
https://www.avast.com/antivirus
------=_NextPart_000_0019_01D6BEB0.2EC2FAE0
charset="UTF-8"
Content-Transfer-Encoding: quoted-printable
<html xmlns:v=3D"urn:schemas-microsoft-com:vml" =
xmlns:o=3D"urn:schemas-microsoft-com:office:office" =
xmlns:w=3D"urn:schemas-microsoft-com:office:word" =
xmlns:m=3D"http://schemas.microsoft.com/office/2004/12/omml"; =
xmlns=3D"http://www.w3.org/TR/REC-html40";><head><meta =
http-equiv=3DContent-Type content=3D"text/html; charset=3Dutf-8"><meta =
name=3DGenerator content=3D"Microsoft Word 15 (filtered medium)"><!--[if =
!mso]><style>v\:* {behavior:url(#default#VML);}
o\:* {behavior:url(#default#VML);}
w\:* {behavior:url(#default#VML);}
.shape {behavior:url(#default#VML);}
</style><![endif]--><style><!--
/* Font Definitions */
@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0cm;
font-size:11.0pt;
font-family:"Calibri",sans-serif;}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
span.E-mailStijl18
{mso-style-type:personal-reply;
font-family:"Calibri",sans-serif;
color:windowtext;}
.MsoChpDefault
{mso-style-type:export-only;
font-family:"Calibri",sans-serif;
mso-fareast-language:EN-US;}
@page WordSection1
{size:612.0pt 792.0pt;
margin:70.85pt 70.85pt 70.85pt 70.85pt;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext=3D"edit" spidmax=3D"1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext=3D"edit">
<o:idmap v:ext=3D"edit" data=3D"1" />
</o:shapelayout></xml><![endif]--></head><body lang=3DNL link=3Dblue =
vlink=3Dpurple style=3D'word-wrap:break-word'><div =
class=3DWordSection1><p class=3DMsoNormal><span lang=3DEN-GB =
style=3D'mso-fareast-language:EN-US'>I have tested the starter outside =
of the car. Bendix works well, but motor runs poorly with lots of =
sparking over the brushes. <o:p></o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB =
style=3D'mso-fareast-language:EN-US'>So I took your advice and it is now =
at the local repair shop. They=E2=80=99ll disassemble it first, in order =
to see it is feasible to do a repair, or a new starter is =
better.<o:p></o:p></span></p><p class=3DMsoNormal><span lang=3DEN-GB =
style=3D'mso-fareast-language:EN-US'><o:p> </o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB =
style=3D'mso-fareast-language:EN-US'>Cheers,<o:p></o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB =
style=3D'mso-fareast-language:EN-US'>Hans<o:p></o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB =
style=3D'mso-fareast-language:EN-US'><o:p> </o:p></span></p><div =
style=3D'border:none;border-top:solid #E1E1E1 1.0pt;padding:3.0pt 0cm =
0cm 0cm'><p class=3DMsoNormal><b>Van:</b> Mgs =
<mgs-bounces@autox.team.net> <b>Namens </b>Richard =
Lindsay<br><b>Verzonden:</b> zondag 15 november 2020 =
14:57<br><b>Aan:</b> Hans Duinhoven =
<h.duinhoven@planet.nl><br><b>CC:</b> mglist =
<mgs@autox.team.net>; MGB-Yahoo =
<mg-mgb@yahoogroups.com><br><b>Onderwerp:</b> Re: [Mgs] Slow =
cranking, was Siphoning Gas<o:p></o:p></p></div><p =
class=3DMsoNormal><o:p> </o:p></p><div><p class=3DMsoNormal>My vote =
is to have your local shop do the rebuild. Turn the commutator on the =
lathe and replace the brushes.<o:p></o:p></p></div><p =
class=3DMsoNormal><o:p> </o:p></p><div><div><p class=3DMsoNormal>On =
Sun, Nov 15, 2020, 7:48 AM <<a =
href=3D"mailto:h.duinhoven@planet.nl";>h.duinhoven@planet.nl</a>> =
wrote:<o:p></o:p></p></div><blockquote =
style=3D'border:none;border-left:solid #CCCCCC 1.0pt;padding:0cm 0cm 0cm =
6.0pt;margin-left:4.8pt;margin-right:0cm'><div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>I measured the voltage on the posts while cranking =3D 10,5 =
volts. It is on a digital meter, so I wonder if that=E2=80=99s a good =
value.</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>The same value is measured on the starter ingoing =
post.</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>So no tension loss on the electrical =
circuits.</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB><br>Now there is a discussion:</span><o:p></o:p></p><p =
class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>Repair the starter or buy a new =
one.</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>High torque starter =3D =E2=82=AC 325,00, which is =
pricy</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>Original starter on exchange base =3D =E2=82=AC =
200,00</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>New starter Powerlite =3D =E2=82=AC =
239,00</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>New starter looking like a Lucas (white labelled) =3D =
=E2=82=AC 135,00</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB> </span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB><a =
href=3D"https://www.octagonparts.nl/product-categorie/mgb/electrical-mgb/=
starting-system-mgb-electrical-mgb/" =
target=3D"_blank">https://www.octagonparts.nl/product-categorie/mgb/elect=
rical-mgb/starting-system-mgb-electrical-mgb/</a> =
</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB> </span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB><a =
href=3D"https://www.angloparts.com/en/catalogues/part/26883/082.024"; =
target=3D"_blank">https://www.angloparts.com/en/catalogues/part/26883/082=
.024</a> </span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB> </span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>There is a local electrical car parts repair shop, where =
the alternator has been repaired +/- 10 years =
ago.</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>They did a good job.</span><o:p></o:p></p><p =
class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>I assume they can fix the starter as well, but what is =
better =E2=80=93 a new one (Angloparts =3D =E2=82=AC 152 or =E2=82=AC =
135,00 at octagonparts) or have the original =
repaired=E2=80=A6</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB> </span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>Cheers,</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>Hans </span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB> </span><o:p></o:p></p><div><div =
style=3D'border:none;border-top:solid #E1E1E1 1.0pt;padding:3.0pt 0cm =
0cm 0cm'><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><b>Van:</b> =
PaulHunt73 <<a href=3D"mailto:paulhunt73@virginmedia.com"; =
target=3D"_blank">paulhunt73@virginmedia.com</a>> =
<br><b>Verzonden:</b> dinsdag 10 november 2020 11:41<br><b>Aan:</b> <a =
href=3D"mailto:h.duinhoven@planet.nl"; =
target=3D"_blank">h.duinhoven@planet.nl</a><br><b>CC:</b> 'mglist' =
<<a href=3D"mailto:mgs@autox.team.net"; =
target=3D"_blank">mgs@autox.team.net</a>>; 'MGB-Yahoo' <<a =
href=3D"mailto:mg-mgb@yahoogroups.com"; =
target=3D"_blank">mg-mgb@yahoogroups.com</a>><br><b>Onderwerp:</b> =
Re: [Mgs] Slow cranking, was Siphoning Gas<o:p></o:p></p></div></div><p =
class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p><div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
style=3D'font-size:10.0pt'>Yes, measure the voltage right on =
the battery posts (adding the two voltages together if twin 6v =
batteries) when cranking, then compare that with the voltage at the =
battery cable stud on the solenoid and starter body when =
cranking. The difference between the two is what is being lost in =
the connections, a volt or so is normal but it shouldn't be much more =
than that.</span><o:p></o:p></p></div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p></div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
style=3D'font-size:10.0pt'>If you get much less than 10v at the battery =
posts then that is the =
problem.</span><o:p></o:p></p></div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p></div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
style=3D'font-size:10.0pt'>PaulH.</span><o:p></o:p></p></div><div><p =
class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p></div></div><blockquote style=3D'border:none;border-left:solid =
black 1.5pt;padding:0cm 0cm 0cm =
4.0pt;margin-left:3.75pt;margin-top:5.0pt;margin-right:0cm;margin-bottom:=
5.0pt'><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
style=3D'font-size:10.0pt;font-family:"Arial",sans-serif'>----- Original =
Message ----- </span><o:p></o:p></p></div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto;background:#E=
4E4E4'><span lang=3DEN-GB =
style=3D'font-size:10.0pt;font-family:"Arial",sans-serif;color:black'>&nb=
sp;</span><o:p></o:p></p></div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>Next job is the slow starter motor. =
</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>I already cleaned the battery posts clamps and the post of =
the battery to chassis cable.</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>Also cleaned thoroughly the chassis to engine cable. =
</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>Nothing helped so far.</span><o:p></o:p></p><p =
class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>So next will be verifying the battery voltage when =
cranking. I assume it will be o.k. as the battery is =
new.</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>Following step will be measuring the voltage over the =
starter motor +12V to the engine.</span><o:p></o:p></p><p =
class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>When o.k., the starter is suspect. As it never was =
overhauled, this is logical.</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB>Nice winter job.</span><o:p></o:p></p><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><span =
lang=3DEN-GB> </span><o:p></o:p></p><div =
style=3D'border:none;border-top:solid #E1E1E1 1.0pt;padding:3.0pt 0cm =
0cm 0cm'><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><b>Van:</b> =
Mgs <<a href=3D"mailto:mgs-bounces@autox.team.net"; =
target=3D"_blank">mgs-bounces@autox.team.net</a>> <b>Namens </b>Dan =
DiBiase<br><b>Verzonden:</b> donderdag 22 oktober 2020 =
22:26<br><b>Aan:</b> Richard Lindsay <<a =
href=3D"mailto:richardolindsay@gmail.com"; =
target=3D"_blank">richardolindsay@gmail.com</a>><br><b>CC:</b> mglist =
<<a href=3D"mailto:mgs@autox.team.net"; =
target=3D"_blank">mgs@autox.team.net</a>>; MGB-Yahoo <<a =
href=3D"mailto:mg-mgb@yahoogroups.com"; =
target=3D"_blank">mg-mgb@yahoogroups.com</a>><br><b>Onderwerp:</b> =
Re: [Mgs] Siphoning Gas<o:p></o:p></p></div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>OMG, duh! =
Thanks to all that replied with this excellent (and obvious, now!) =
advice..............................<o:p></o:p></p><div><p =
class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p></div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>Dan D<br =
clear=3Dall><o:p></o:p></p><div><div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><a =
href=3D"http://dandibiase.cbintouch.com/"; =
target=3D"_blank">http://dandibiase.cbintouch.com/</a><o:p></o:p></p></di=
v></div></div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p></div></div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p><div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>On Thu, Oct =
22, 2020 at 4:13 PM Richard Lindsay <<a =
href=3D"mailto:richardolindsay@gmail.com"; =
target=3D"_blank">richardolindsay@gmail.com</a>> =
wrote:<o:p></o:p></p></div><blockquote =
style=3D'border:none;border-left:solid #CCCCCC 1.0pt;padding:0cm 0cm 0cm =
6.0pt;margin-left:4.8pt;margin-top:5.0pt;margin-right:0cm;margin-bottom:5=
.0pt'><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>I had the =
same problem. I disconnected the fuel hose, added a a long bit of hose =
and with the coil disconnected, used the fuel pump to pump old fuel into =
jugs.<o:p></o:p></p></div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p><div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>On Thu, Oct =
22, 2020, 3:02 PM Dan DiBiase <<a =
href=3D"mailto:dan.dibiase@gmail.com"; =
target=3D"_blank">dan.dibiase@gmail.com</a>> =
wrote:<o:p></o:p></p></div><blockquote =
style=3D'border:none;border-left:solid #CCCCCC 1.0pt;padding:0cm 0cm 0cm =
6.0pt;margin-left:4.8pt;margin-top:5.0pt;margin-right:0cm;margin-bottom:5=
.0pt'><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>Hi all.... =
My '76B, which was off the road for 5 years, was recently returned =
to me from the shop. They added some new gas but did not siphon out the =
5 year old gas (which was just under 1/2 tank when I had it towed in. =
The car is running pretty rough so I want to siphon out most of the gas =
before I fill it up. It is currently showing as just under 1/2 tank, so =
around 6 gallons or a little less (assuming gauge =
accuracy). <o:p></o:p></p><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p></div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>I was able =
to pump out about 2 gallons but am wondering if the interior of the tank =
is baffled, as I can't seem to move the hose beyond a certain area and =
it's not sucking up any additional gas. Would really like to remove a =
couple more gallons before I fill it up.<o:p></o:p></p></div><div><p =
class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p></div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>Thx, <o=
:p></o:p></p></div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p></div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>Dan =
D<o:p></o:p></p></div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>'76B- =
Getting There<o:p></o:p></p></div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>'65B - =
Waiting It's Turn<o:p></o:p></p></div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>Central NJ =
USA<br clear=3Dall><o:p></o:p></p><div><div><div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><a =
href=3D"http://dandibiase.cbintouch.com/"; =
target=3D"_blank">http://dandibiase.cbintouch.com/</a><o:p></o:p></p></di=
v></div></div></div></div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>____________=
___________________________________<br><br><a =
href=3D"mailto:Mgs@autox.team.net"; =
target=3D"_blank">Mgs@autox.team.net</a><br>Donate: <a =
href=3D"http://www.team.net/donate.html"; =
target=3D"_blank">http://www.team.net/donate.html</a><br>Suggested =
annual donation $12.75<br><br>Archive: <a =
href=3D"http://www.team.net/pipermail/mgs"; =
target=3D"_blank">http://www.team.net/pipermail/mgs</a> <a =
href=3D"http://autox.team.net/archive"; =
target=3D"_blank">http://autox.team.net/archive</a><br><br>Unsubscribe: =
<a =
href=3D"http://autox.team.net/mailman/options/mgs/richardolindsay@gmail.c=
om" =
target=3D"_blank">http://autox.team.net/mailman/options/mgs/richardolinds=
ay@gmail.com</a><o:p></o:p></p></blockquote></div></blockquote></div><div=
id=3D"m_-633492779099770990DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2"><p =
class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'> <o:p><=
/o:p></p><table class=3DMsoNormalTable border=3D1 cellspacing=3D3 =
cellpadding=3D0 style=3D'border:none;border-top:solid #D3D4DE =
1.0pt'><tr><td width=3D55 =
style=3D'width:41.25pt;border:none;padding:13.5pt .75pt .75pt .75pt'><p =
class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'><a =
href=3D"https://www.avast.com/sig-email?utm_medium=3Demail&utm_source=
=3Dlink&utm_campaign=3Dsig-email&utm_content=3Demailclient" =
target=3D"_blank"><span style=3D'text-decoration:none'><img border=3D0 =
width=3D46 height=3D29 style=3D'width:.4833in;height:.3in' =
id=3D"_x0000_i1027" =
src=3D"https://ipmcdn.avast.com/images/icons/icon-envelope-tick-round-ora=
nge-animated-no-repeat-v1.gif"></span></a><o:p></o:p></p></td><td =
width=3D470 style=3D'width:352.5pt;border:none;padding:12.75pt .75pt =
.75pt .75pt'><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto;line-height:1=
3.5pt'><span =
style=3D'font-size:10.0pt;font-family:"Arial",sans-serif;color:#41424E'>V=
irusvrij. <a =
href=3D"https://www.avast.com/sig-email?utm_medium=3Demail&utm_source=
=3Dlink&utm_campaign=3Dsig-email&utm_content=3Demailclient" =
target=3D"_blank"><span style=3D'color:#4453EA'>www.avast.com</span></a> =
</span><o:p></o:p></p></td></tr></table></div><div class=3DMsoNormal =
align=3Dcenter style=3D'text-align:center'><hr size=3D2 width=3D"100%" =
align=3Dcenter></div><p class=3DMsoNormal =
style=3D'mso-margin-top-alt:auto;mso-margin-bottom-alt:auto'>____________=
___________________________________<br><br><a =
href=3D"mailto:Mgs@autox.team.net"; =
target=3D"_blank">Mgs@autox.team.net</a><br>Donate: <a =
href=3D"http://www.team.net/donate.html"; =
target=3D"_blank">http://www.team.net/donate.html</a><br>Suggested =
annual donation $12.75<br><br>Archive: <a =
href=3D"http://www.team.net/pipermail/mgs"; =
target=3D"_blank">http://www.team.net/pipermail/mgs</a> <a =
href=3D"http://autox.team.net/archive"; =
target=3D"_blank">http://autox.team.net/archive</a><br><br>Unsubscribe: =
<a =
href=3D"http://autox.team.net/mailman/options/mgs/paulhunt73@virginmedia.=
com" =
target=3D"_blank">http://autox.team.net/mailman/options/mgs/paulhunt73@vi=
rginmedia.com</a><o:p></o:p></p></blockquote></div></div><p =
class=3DMsoNormal>_______________________________________________<br><br>=
<a href=3D"mailto:Mgs@autox.team.net"; =
target=3D"_blank">Mgs@autox.team.net</a><br>Donate: <a =
href=3D"http://www.team.net/donate.html"; =
target=3D"_blank">http://www.team.net/donate.html</a><br>Suggested =
annual donation $12.75<br><br>Archive: <a =
href=3D"http://www.team.net/pipermail/mgs"; =
target=3D"_blank">http://www.team.net/pipermail/mgs</a> <a =
href=3D"http://autox.team.net/archive"; =
target=3D"_blank">http://autox.team.net/archive</a><br><br>Unsubscribe: =
<a =
href=3D"http://autox.team.net/mailman/options/mgs/richardolindsay@gmail.c=
om" =
target=3D"_blank">http://autox.team.net/mailman/options/mgs/richardolinds=
ay@gmail.com</a><o:p></o:p></p></blockquote></div></div></body></html>
------=_NextPart_000_0019_01D6BEB0.2EC2FAE0--
--===============7212010651841810864==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Mgs@autox.team.net
Archive: http://www.team.net/pipermail/mgs http://autox.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/mgs/mharc@autox.team.net
--===============7212010651841810864==--
|