I broke an easy out in a bolt in my boat motor. Impossible to drill. I took
a very small (very small) bit and drilled alot of holes around it (kinda
like cutting it out) until i could get it out. Then I drilled the hole one
size over (because I probably messed up the threads) and put a helicoil in.
This was a bolt for the waterjacket cover and hasn't leaked in about 3
years. Your working on a smaller bolt than I was though.
----- Original Message -----
From: Don Slaney <firstname.lastname@example.org>
To: Murray Whitlock <email@example.com>; <Hudson29@aol.com>;
Sent: Friday, November 26, 1999 9:08 PM
Subject: Re: [oletrucks] Howdyaget an "Easy Out" Out?
> After all I see here, my easy outs are on the way out!!!! There must be
> easier "out" ways.
> Regards to all,
> ----- Original Message -----
> From: Murray Whitlock <firstname.lastname@example.org>
> To: <Hudson29@aol.com>; <email@example.com>;
> Sent: Friday, November 26, 1999 7:24 PM
> Subject: Re: [oletrucks] Howdyaget an "Easy Out" Out?
> > Paul: If you have access to a welder, here is what i have used here on
> > farm to get brocken bolts out. I take a washer with the same size hole
> > the bolt, place it over the brocken off end of the bolt, and weld it on
> > through the hole. Completely filling the hole of the washer with weld.
> > I take a nut , smaller in diameter than the washer and weld that to the
> > washer, with all the welding, usually the brocken piece is heated up
> > red, and with a turn of a wrench will twist out. Espeacially with the
> > brocken off extractor still in there. I realize that doing under the
> > over head, may be a challenge, but think it should work. Good luck!
> > 51 chev. Work in progress
> > 72 chev. restored.
> > -----Original Message-----
> > From: Hudson29@aol.com <Hudson29@aol.com>
> > To: firstname.lastname@example.org <email@example.com>;
> > firstname.lastname@example.org <email@example.com>
> > Date: Friday, November 26, 1999 5:20 PM
> > Subject: [oletrucks] Howdyaget an "Easy Out" Out?
> > > I'm back to work today on the same broken bolt that stymied me
> > >weeks ago. The first part of the job was to use a Dremel Moto Tool to
> > >the shaft of the broken bolt level inside the hole. Once this was done
> > >figured on using the new toys the Snap-On guy delivered Wednesday, an
> > >extractor set with drill guides. I had high hopes for the drill guides,
> > >bumped into an unpleasant surprise before I could use them.
> > > The Dremel with a rotary grinding bit did clean up the hole so that
> > >could see what was going on, and it looks like a metallic five pointed
> > >is imbedded in the broken bolt. It is very tough, and even the new
> > >drills won't touch it, just skating across the surface. Could this be
> > is
> > >left of an "Easy-Out" that somebody broke off and just gave up on?
> > > What now? I think I'll go back out and work with the Dremel awhile,
> > I
> > >doubt that will get much further down. I would sure hate to have to
> > the
> > >entire motor out to a machine shop to have one oil pan bolt removed,
> > I'm
> > >runnin' out of ideas.
> > >
> > >Paul O'Neil, Hudson29@aol.com
> > >1951 Chevrolet 3600 Pickup Project, See it at:
> > >The Poor Man's Advanced Design Tech Tips Page
> > >http://home.earthlink.net/~conntest47/
> > >Fullerton, California USA
> > >AEROMARK - Need Rubber Stamps or Signs? See:
> > >http://www.aeromark.net
> > >oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
> > oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
> oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959