Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Engine\s+lifting\s+points\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Engine\s+lifting\s+points\s*$/: 7 ]

Total 7 documents matching your query.

1. Engine lifting points (score: 1): Author: John Hogan <mad@madgrizzle.com>; Date: Sat, 02 Feb 2002 18:20:56 -0500; Everything has been disconnected but I'm not sure where on the engine to hook the lifting chains. The service manual shows the front and the back of the engine, but I don't know specifically where in; /html/datsun-roadsters/2002-02/msg00065.html (7,217 bytes)
2. Re: Engine lifting points (score: 1): Author: "Andrew Murphy" <solex67@hotmail.com>; Date: Sat, 02 Feb 2002 15:53:18 -0800; Are the lifting eyelets in place? There are two metal eyelets located at the front and rear of the head that stick up and allow for the balancer chains to go through. They are also installed on my 1; /html/datsun-roadsters/2002-02/msg00067.html (8,023 bytes)
3. Re: Engine lifting points (score: 1): Author: John Hogan <mad@madgrizzle.com>; Date: Sat, 02 Feb 2002 19:31:41 -0500; Ah.. well, apparently the answer is no. :) So its a couple of bolt on eyelets, eh? Well.. the hooks for the engine tilter are actually L-shaped brackets with a bolt hole on the vertical and horizonta; /html/datsun-roadsters/2002-02/msg00068.html (7,725 bytes)
4. Re: Engine lifting points (score: 1): Author: "Deena Petrie" <dpetrie@megsinet.net>; Date: Sat, 2 Feb 2002 19:38:00 -0600; You would use the head bolts. The L bracket would be on the head bolt. 1 in each opposite corner. Hope this helps. I tried to find the photos but was un able. Deena & Joe 69 1600 in progress Westmont; /html/datsun-roadsters/2002-02/msg00073.html (8,750 bytes)
5. Re: Engine lifting points (score: 1): Author: "Andrew Murphy" <solex67@hotmail.com>; Date: Sat, 02 Feb 2002 17:57:43 -0800; I also looked for some pics but couldn't find any. They are mounted on the head bolts, one on the driver side rear and the other on the driver side front. The front eyelet is straight, while the rear; /html/datsun-roadsters/2002-02/msg00074.html (8,428 bytes)
6. Re: Engine lifting points (score: 1): Author: "datsunmike" <datsunmike@nyc.rr.com>; Date: Sat, 2 Feb 2002 20:28:21 -0500; The rear mount is connected to the last 2 manifold studs on the verticle. The front should be connected to a stud on the front of the head. I also had this problem on a parts car I bought. I connecte; /html/datsun-roadsters/2002-02/msg00075.html (9,183 bytes)
7. Re: Engine lifting points (score: 1): Author: "datsunmike" <datsunmike@nyc.rr.com>; Date: Sat, 2 Feb 2002 21:44:20 -0500; I guess the L brackets aren't useless if you use the head bolts as previously mentioned. I never used the head bolts to pull an engine. Mike chain head. L-shaped at /// datsun-roadsters@autox.team.ne; /html/datsun-roadsters/2002-02/msg00085.html (10,446 bytes)

Current List: 1 - 7
Page: [1]