Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Torque\s+settings\s+for\s+Rover\s+exhaust\s+manifolds\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Torque\s+settings\s+for\s+Rover\s+exhaust\s+manifolds\s*$/: 12 ]

Total 12 documents matching your query.

1. Torque settings for Rover exhaust manifolds (score: 1): Author: Paul.Kile@Aerojet.com (KILE, PAUL D); Date: Tue, 17 Oct 2000 07:11:25 -0700; Hi guys, I'm getting ready to bolt the exhaust manifolds onto my 3.5 for my factory MGB-GT V-8. The factory recommends 13 foot-pounds for the bolt torque, but that is for the original specification w; /html/buick-rover-v8/2000-10/msg00049.html (8,234 bytes)
2. Re: Torque settings for Rover exhaust manifolds (score: 1): Author: Jim Stuart <jimbb88@erols.com>; Date: Tue, 17 Oct 2000 19:49:09 -0400; While there are no illustrations of an exhaust manifold gasket in the MGB GT V8 Workshop Manual Supplement, I can't believe that these engines were built (by the factory) without them. It is almost; /html/buick-rover-v8/2000-10/msg00053.html (9,913 bytes)
3. Re: Torque settings for Rover exhaust manifolds (score: 1): Author: lmg@gomog.com; Date: Tue, 17 Oct 2000 20:46:47 -0400; Hi Jim and Paul, Jim, you and I have curiously different materiel to consult. I have opened up a number of SD1s and Vitesses. I have never found a set of gaskets on either manifolds or heddars. The s; /html/buick-rover-v8/2000-10/msg00055.html (8,538 bytes)
4. Re: Torque settings for Rover exhaust manifolds (score: 1): Author: David Kernberger <dkern@napanet.net>; Date: Tue, 17 Oct 2000 17:57:45 -0700; Jim, The 61-63 Olds F-85 ex. manifolds came originally without gaskets. Studs, nuts, and flat washers were used. The factory manual shows a torque spec of 18-24 ft. lb. KDon't know if this helps. Re; /html/buick-rover-v8/2000-10/msg00056.html (10,560 bytes)
5. Re: Torque settings for Rover exhaust manifolds (score: 1): Author: Jim Stuart <jimbb88@erols.com>; Date: Tue, 17 Oct 2000 21:29:51 -0400; As I said, My shop manual is silent regards gaskets. This manual is part # AKM 3616B copyright 1981. The parts manual is part # RTC9852CA dated January 1980. Since it shows the gasket as #GEG692, man; /html/buick-rover-v8/2000-10/msg00058.html (9,422 bytes)
6. RE: Torque settings for Rover exhaust manifolds (score: 1): Author: "Jim Patterson" <jim@rover-v8.co.uk>; Date: Wed, 18 Oct 2000 12:00:51 +0100; Hi all, I have scanned the entire AKM 3616B Workshop manual The address is http://members.tripod.co.uk/roverv8/sd1.htm I still have a lot of work to do linking the site together, but you should Still; /html/buick-rover-v8/2000-10/msg00062.html (9,604 bytes)
7. RE: Torque settings for Rover exhaust manifolds (score: 1): Author: Paul.Kile@Aerojet.com (KILE, PAUL D); Date: Wed, 18 Oct 2000 07:14:09 -0700; I was amazed too when I found that the factory GT V-8 used no exhaust manifold gaskets as stock. When I visited Beer of Houghton (one of the foremost MG V-8 shops in the UK) Syd and Malcolm confirme; /html/buick-rover-v8/2000-10/msg00063.html (12,227 bytes)
8. RE: Torque settings for Rover exhaust manifolds (score: 1): Author: Paul.Kile@Aerojet.com (KILE, PAUL D); Date: Wed, 18 Oct 2000 07:35:00 -0700; I may have an explanation - I think the GEG 692 manifold gaskets were only used on EXPORT SD1s. I seem to recall the Beers mentioning that fact when I talked to them in the UK. Can't tell from your; /html/buick-rover-v8/2000-10/msg00065.html (9,192 bytes)
9. RE: Torque settings for Rover exhaust manifolds (score: 1): Author: "James R Bown" <Bowan@uswest.net>; Date: Wed, 18 Oct 2000 08:41:34 -0600; I have never seen either an Olds or Buick 215 that came from the factory with exhaust manifold gaskets. I personally always use gaskets when reassembling them however. Regards, Jim Bown --Original Me; /html/buick-rover-v8/2000-10/msg00067.html (10,119 bytes)
10. RE: Torque settings for Rover exhaust manifolds (score: 1): Author: "Larry Hoy" <larryhoy@prodigy.net>; Date: Wed, 18 Oct 2000 09:00:22 -0600; While Jim may be correct with the Rover variation of the aluminum V8, the 1961 Buick service manual says, "No gaskets are used in the entire exhaust system." The 1961 Oldsmobile service manual indic; /html/buick-rover-v8/2000-10/msg00070.html (8,652 bytes)
11. Re: Torque settings for Rover exhaust manifolds (score: 1): Author: "The Becketts" <hillman@bigpond.com>; Date: Wed, 18 Oct 2000 19:50:23 +1000; Paul Kile asked: Paul, the exhaust manifold torque settings are, according to my 1986 RR manual, 14-16 ft lbs Ron Beckett 1986 Range Rover HiLine Auto 4.6 Litre; /html/buick-rover-v8/2000-10/msg00072.html (8,335 bytes)
12. RE: Torque settings for Rover exhaust manifolds (score: 1): Author: "Bown" <Bown@concentric.net>; Date: Sun, 29 Oct 2000 21:35:28 -0700; Would you be so kind as to post the Felpro and Victor numbers for the exhaust manifold gaskets. (The kids running the parts counter at my local auto-parts house aren't too bright) Regards, Jim B. --O; /html/buick-rover-v8/2000-10/msg00082.html (10,032 bytes)

Current List: 1 - 12
Page: [1]