tigers
[Top] [All Lists]

Re: [Tigers] Tiger Cooling

To: "Smit, Theo" <Theo.Smit@dynastream.com>, <CoolVT@aol.com>, <tigers@autox.team.net>, <dave@munroe.ca>
Subject: Re: [Tigers] Tiger Cooling
From: "James Lindner" <jliny5@cox.net>
Date: Wed, 21 Mar 2012 12:52:48 -0400
Authentication-results: cox.net; none
Delivered-to: tigers-archive@autox.team.net
Delivered-to: tigers@autox.team.net
List-archive: <http://autox.team.net/pipermail/tigers>
List-help: <mailto:tigers-request@autox.team.net?subject=help>
List-id: Sunbeam Tigers <tigers.autox.team.net>
List-post: <mailto:tigers@autox.team.net>
List-subscribe: <http://autox.team.net/mailman/listinfo/tigers>, <mailto:tigers-request@autox.team.net?subject=subscribe>
List-unsubscribe: <http://autox.team.net/mailman/options/tigers>, <mailto:tigers-request@autox.team.net?subject=unsubscribe>
References: <43b31.5b3227e5.3c9b5c91@aol.com> <47A9A7829443AE49853415B6D05B0684063C601C7B@OLE2K7CCR1.ad.garmin.com>
Hi All

I would really appreciate if somebody could share with me a photo(s) of the 
locations where you have inserted foam to block gaps. I have the horn holes 
blocked, six blade fan and I am getting ready to install a reduced diameter 
pulley. Blocking the gaps seems like another logical step.

Thanks

Jim

-----Original Message----- 
From: Smit, Theo
Sent: Wednesday, March 21, 2012 12:42 PM
To: CoolVT@aol.com ; tigers@autox.team.net ; dave@munroe.ca
Subject: Re: [Tigers] Tiger Cooling

Hi Mark,
I don't think that there are any quick cooling aids for the Tiger - all of
them require attention to detail to get more than just a marginal benefit.

The Cressida fan is about 12" diameter and has an integrated steel shroud; 
it
just barely fits below the sheetmetal in the nose. I used foam adhesive tape
to seal the gap between the rad matrix and the shroud. The problem you 
always
have with pusher fans is that the motor obscures some of the available area; 
a
second thing is that if the gaps aren't filled, then the air can just go out
the side rather than through the radiator. The reason why I used this fan is
that it was evidently designed from the outset as a pusher application. A 
lot
of aftermarket fans are designed as a puller, and then when they're used in 
a
pusher application they really don't move anywhere near the air that they're
supposedly rated at.

The only thing that would be nice is to have a similar fan, but larger, so
that it would move more air over more of the radiator. You'd end up with 
part
of the fan output deadheading against the lower radiator support though.

Moving air through half the rad should be more than sufficient, since the 
fan
is only required to boost airflow at low speeds. You just have to make sure
that the air you're moving is really going through the rad rather than 
around
it, and that it's moving with sufficient speed.
A secondary issue is that if the fan only covers part of the radiator core,
are those core tubes actually flowing enough coolant to do the job?

Theo

________________________________
This e-mail and any attachments may contain confidential material for the 
sole
use of the intended recipient. If you are not the intended recipient, please
be aware that any disclosure, copying, distribution or use of this e-mail or
any attachment is prohibited. If you have received this e-mail in error,
please contact the sender and delete all copies.

Thank you for your cooperation.
_______________________________________________

tigers@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: http://autox.team.net/mailman/options/tigers/jliny5@cox.net
_______________________________________________

tigers@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: 
http://autox.team.net/mailman/options/tigers/tigers-archive@autox.team.net



<Prev in Thread] Current Thread [Next in Thread>