Well after a year of nagging her my wife said OK to a compressor. This will be a once in a lifetime buy. I am not able to buy one now and then if a few years think about getting a better one. So this
If you wait until the 7th of June you can save another $10.00 by using you craftsman club card. If you are not a member you can join for free and save - forever... NHJim 46 Chevy 3104 Jim, Just so ha
Bob and list, Thanks to all for the input. I am sure that I have started this hobby like so many of you. But now 2 years into it I still think this will be my ONLY truck. I know that this may be pie
I am looking for the light that goes behind the center of the dash and has a switch under the dash. This is often called a curtsey light. Do you have one or know where I might be able to find one? Th
do you have any more of those 41/46 rear fenders? I am looking for the bottom 1/2 for the driver side. Also, I am looking for information on the support bracket(s). I was told that for the 45 and 46
Well in another famous what can I do in an hour - I decided to sand and paint the crank out windshield in the 46. I did not mask off or tape - just fired up the sander and went after the rusty medal.
I know of one for the 40-46 in a yard that I should be at in the next few days. They had 2 and I got the best one (lower part only) but the other is not that bad. I am only using the bottom and it wa
I have taken pictures of a jack that Jim Carter sent me as original for my 46. However the jack is not working. And after 5 calls (about a month apart) to the used parts department, each time they to
Page 8 of the owners manual go into great detail on how this switch works. This manual calls this light the "ASH RECEIVER LIGHT". It should be a 3 way switch, mine is only 2 way. What a surprise - I
Yesterday I stated I would never purchase another truck. However I would love to have this one. Oh the thing I could do with that baby..... NHJim 46 Chevy 3104 Hey list... Has anyone ever seen anyth
Speaking of trucks we have seen. Last year I was in Idaho, on the back side of the Tetons there is a Drive-In Theater with a GMC 2+ ton that has the billboard of what is showing parked out front. Has
In one of the first books I purchased there is a demo of changing from 3 to 5. What they did is cut off the tops of both trucks and welded back on the five. Above the windshield post in the front and
For the first time I took my digital camera to the Junk Yard. Took over 150 photos - I will shrink them and post them to my web site later this month. However I did get some great parts. I found and
Take a look for more info: I know Bob ADler will be there and I hope to make it as well. NHJim 45 Chevy 3104 oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
Using the internet I have used a AT&T web site: http://www.anywho.com In the past you could enter a street and it would give you everyone on the street. Now if you know the company name you can find
I have a question for you. What pressurized blaster do you have. Where did you purchase it and for how much (if you want to tell). Also what do you like and diskine about your unit. I am doing one tr
I now have my compressor and am looking at pressurized blaster. The lowest price that I can find is at Harbor Freight. There are two units I am now looking at: 40 lb unit for $89.99 http://www.harbor
Yes I did. I found a package deal. What was included a male/female stem and female quick connect body. Includes 1/4 in. x 25 ft. coil hose, 1/4 in. connector, Florida Pneumatic ratchet (Sears 009/188
Take a look at my web page. I have since purchased a Master Parts Catalog covering 1929-1950. It has the best photo I have ever seen, I hope to scan it and add it to this page (soon). This is looking
I have purchased replacement cables at a truck show last week. In order to remove the old cables I needed to cut them and then I could get both sides removed from the backing plate. The cables I purc