Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[6pack\]\s+Bouncing\s+Speedo\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[6pack\]\s+Bouncing\s+Speedo\s*$/: 11 ]

Total 11 documents matching your query.

1. [6pack] Bouncing speedo (score: 1): Author: "Bruce Moxon" <bamxn@triad.rr.com>; Date: Fri, 20 Jul 2007 21:15:38 -0400; My speedo needle tends to bounce, especially at lower speeds and when down shifting. At cruising speed, I just average the bounce to guess at my speed. I have a new cable, rebuilt tranny(A type OD),; /html/6pack/2007-07/msg00169.html (6,707 bytes)
2. RE: [6pack] Bouncing Speedo (score: 1): Author: "Robert Liam Gannon" <trsix74@comcast.net>; Date: Fri, 20 Jul 2007 21:46:04 -0400; Bruce wrote: My Speedo needle tends to bounce, especially at lower speeds and when down shifting. At cruising speed, I just average the bounce to guess at my speed. I have a new cable, rebuilt tranny; /html/6pack/2007-07/msg00170.html (7,519 bytes)
3. RE: [6pack] Bouncing Speedo (score: 1): Author: "Robert Liam Gannon" <trsix74@comcast.net>; Date: Sat, 21 Jul 2007 07:24:35 -0400; The 3/8's should be measured at the speedometer end. Insert the inner cable into the sheath until it will not go any further. At that point, you try turning the inner cable by hand to make sure it is; /html/6pack/2007-07/msg00171.html (7,251 bytes)
4. Re: [6pack] Bouncing Speedo (score: 1): Author: James Franks <jimmble@adelphia.net>; Date: Sat, 21 Jul 2007 07:51:09 -0400; This is a really good tip Robert. Thanks for that! Thinking about it, if I were to run into this, I might try fitting a spacer inside the angle drive at the gearbox attachment side to take up the nee; /html/6pack/2007-07/msg00172.html (7,684 bytes)
5. Re: [6pack] Bouncing Speedo (score: 1): Author: Dave & M <rusd@sitestar.net>; Date: Sat, 21 Jul 2007 06:21:21 -0600; Some of the replacement cables have a plastic bushing/bearing at the upper/speedometer end, the originals were metal. In addition to the 3/8" maximum mentioned, make sure that no part of the bushing; /html/6pack/2007-07/msg00174.html (7,299 bytes)
6. [6pack] Bouncing Speedo (score: 1): Author: "Steve Kirsis" <sakirsis@consolidated.net>; Date: Sat, 21 Jul 2007 12:25:09 -0500; Moss recommends a copper washer between either the cable and the right angle or the tranny and the right angle (can't remember which) and will insist on selling you one. I installed their washers in; /html/6pack/2007-07/msg00176.html (6,762 bytes)
7. Re: [6pack] Bouncing Speedo (score: 1): Author: "Bruce Moxon" <bamxn@triad.rr.com>; Date: Sun, 22 Jul 2007 17:04:21 -0400; You did mean trim the speedo end of the cable not the angle drive end? The speedo end has the plastic bush/stop that does not allow it to go further into the sleeve. I did measure it and it is about; /html/6pack/2007-07/msg00179.html (8,186 bytes)
8. RE: [6pack] Bouncing Speedo (score: 1): Author: "Stephen Hanselman" <tr6@kc4sw.com>; Date: Mon, 23 Jul 2007 09:06:35 -0700; Robert is spot on about the grease. In fact if the length issue doesn't fix the problem look at the lube you used on the cable. I had problems with both a bouncing speedo and shifting on a GMC van.; /html/6pack/2007-07/msg00182.html (8,101 bytes)
9. Re: [6pack] Bouncing Speedo (score: 1): Author: "Bruce Moxon" <bamxn@triad.rr.com>; Date: Fri, 27 Jul 2007 10:29:49 -0400; I'd like to thank all who responded to my annoying problem. I ground the speedo end of the cable to get the proper length and also lubricated the cable with lithium grease and have not elimated, but; /html/6pack/2007-07/msg00211.html (9,119 bytes)
10. Re: [6pack] Bouncing Speedo (score: 1): Author: tr6taylor@webtv.net (Sally or Dick Taylor); Date: Fri, 27 Jul 2007 11:17:03 -0700; Bruce--Sometimes when a bouncing speedo needle persists, it is good to take the cable and what drives it out of the picture. A length of old speedo cable cut to about a foot long can test the speedo; /html/6pack/2007-07/msg00213.html (8,159 bytes)
11. RE: [6pack] Bouncing Speedo (score: 1): Author: "Navarrette, Vance" <vance.navarrette@intel.com>; Date: Fri, 27 Jul 2007 13:24:52 -0700; My speedo bounces a small amount. I noticed that if I turned the speedo by hand using a small screwdriver, there was a brief increase in turning force required every few turns. It was when this incr; /html/6pack/2007-07/msg00215.html (9,797 bytes)

Current List: 1 - 11
Page: [1]